Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: beege

Page 1 of 38 1 2 3 4

Search: Search took 0.02 seconds.

  1. Have you looked at Palmgren ...

    Have you looked at Palmgren or Louis Levin?
  2. Replies
    2
    Views
    315

    D60, D675, found here...

    D60, D675, found here?
  3. Replies
    5
    Views
    630

    The configuration shown was designed to drive...

    The configuration shown was designed to drive burrs towards the middle of the cutter. Down on the topside, up on the bottom. marketed as mills for composite materials. 'Nuther link here.
  4. Replies
    15
    Views
    1,070

    Haven't used Fanuc in a while. Do you have to...

    Haven't used Fanuc in a while. Do you have to cancel G10 mode with a G11?
  5. Replies
    36
    Views
    7,752

    Maybe cut once with the tool center on part axis,...

    Maybe cut once with the tool center on part axis, once with tool edge on part axis and one in the middle for show, and it would be mostly flat.
  6. Replies
    2
    Views
    1,294

    Indicator Stands and Calibration

    I have several CI indicator stands, and the Indicators on them are calibrated in our company's system. We have our granite surface plates serviced and calibrated at regular intervals. What about...
  7. Replies
    9
    Views
    633

    P-Cancel when powering up clears overtravel. I...

    P-Cancel when powering up clears overtravel. I think.
  8. I think it depends on the control and its usage....

    I think it depends on the control and its usage. I've seen Inch/metric as G20/21 and G70/71. And G50 used the same as G92 to set work coordinates and spindle speed., but G92 is also a threading cycle...
  9. AND All planes (G17 - XY, G18 - XZ and G19 - YZ)...

    AND
    All planes (G17 - XY, G18 - XZ and G19 - YZ) are viewed/imagined from the perspective of the X+ Y+ Z+ quadrant. So, not only MIGHT the radii look backwards from the operator's standpoint, the...
  10. G28 G91 Z0 There are two moves commanded in...

    G28 G91 Z0

    There are two moves commanded in that one line.
    G28 goes home through a point, Z0. It doesn't command the tool to move to a machine Z0
    If you were in absolute, the tool would move to...
  11. Father-in-law had babebiosis - not pleasant at...

    Father-in-law had babebiosis - not pleasant at all another one of the tick-borne diseases. Check this site...
  12. Long time ago, fixed a rubber/canvas cover with...

    Long time ago, fixed a rubber/canvas cover with an old tire tube and some weatherstrip adhesive. Had to clean and scuff up both surfaces, but it worked for a while.
  13. Replies
    18
    Views
    1,373

    I really hate telling anyone this, but you could...

    I really hate telling anyone this, but you could use G92 instead. Put a G92 X0Y0 at the top of the program, indicate the center of your part and press go? I've never done that myself, because I don't...
  14. I think the best option is to find work that's...

    I think the best option is to find work that's hard, then find ways to make it easy.
  15. Replies
    0
    Views
    539

    Position Opening in SE Mass

    I have a position (CNC Operator or better) I'm working to fill in North Attleboro, MA. I have two Haas TM1's and a VF2SSYT. All non-ferrous milling/drilling, three axes only. My HR person has feelers...
  16. Thread: Help Finding

    by beege
    Replies
    15
    Views
    901

    Your picture could use some scale. A quarter, a...

    Your picture could use some scale. A quarter, a dollar bill... or tell us what size holes it has. Something. (now that you've been well-chastised) It almost looks like this at Flexbar.
  17. You can try Meyer Gage...

    You can try Meyer Gage?

    I have a metrology sales company near me that I'd go through in an emergency. Also, Boston Centerless (also near me) had some people that used to work at Van Keuren.
  18. Does M03 even work? Perhaps you have an aliased...

    Does M03 even work? Perhaps you have an aliased M03?
  19. Don't end with a "G91 G28 Z0". Use a "G53 Z4.3"...

    Don't end with a "G91 G28 Z0". Use a "G53 Z4.3" (find out what your machine Z position is at its highest). Then G53 to a safe tool change position on X and Y. Then, after the tool change, use "G53...
  20. Replies
    223
    Views
    37,388

    Has anyone test-driven KeyCreator...

    Has anyone test-driven KeyCreator? They used to be Cadkey, and I believe they spun off from Mastercam years ago. I'd be interested to see some opinions. They a local to me in MA
  21. Replies
    6
    Views
    357

    M99 returns to (start) or if you M99P###, will...

    M99 returns to (start) or if you M99P###, will return to N###
  22. Replies
    6
    Views
    798

    You're in Australia? I've no clue what available...

    You're in Australia? I've no clue what available to you. I'm using a subplate with ball locks on them, which other plates can mounted to. So, keeping the subplate rather simple, I can swap out outer...
  23. Replies
    40
    Views
    2,508

    This sounds like an application for 3D printing,...

    This sounds like an application for 3D printing, since it is very hard to get access to these holes from such a small bore
  24. Replies
    18
    Views
    1,311

    I use a desktop PC, so I use: ALT+248 as degree...

    I use a desktop PC, so I use:
    ALT+248 as degree °
    ALT+241 as plus/minus ±
    ALT+0216 as diameter Ø
    I also have an employee with an accented name, has an é in it, which is ALT+130
  25. Replies
    5
    Views
    597

    But I think if you use G52, that would be a...

    But I think if you use G52, that would be a better answer. Using G10 has the potential of losing your starting point, especially if your cycle is interrupted.
Results 1 to 25 of 938
Page 1 of 38 1 2 3 4