Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: e-fishin-c

Page 1 of 11 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    56
    Views
    2,784

    I’d check this out as well, years ago I was...

    I’d check this out as well, years ago I was troubleshooting a hyd baler in a grocery store and I detected too much voltage drop because of an air conditioner unit that was wired improperly...
  2. Replies
    72
    Views
    5,083

    I received a $2400 debit card in the mail last...

    I received a $2400 debit card in the mail last week. I almost threw it in the trash thinking it was a scam for another credit card, but it was real. Today I received the exact same letter with DJT...
  3. Replies
    105
    Views
    8,198

    Yikes, while I sympathize with the OP I need to...

    Yikes, while I sympathize with the OP I need to read these threads occasionally to realize how fortunate I am. Back in the winter my riggers had a 9200# Hurco loaded up (40 miles away), we left at...
  4. Replies
    14
    Views
    1,238

    Bore Repair Systems, Inc. bore welding and line...

    Bore Repair Systems, Inc. bore welding and line boring systems

    I use this system, the welding head moves .100” per rev, the feed is fixed but welding speed is variable.
  5. Replies
    7
    Views
    779

    You may have burnt up the shaft seal from the...

    You may have burnt up the shaft seal from the lack of oil, try globbing a couple of finger fulls of new grease at the pump shaft area to see if it’s sucking air thru the shaft seal. Opening up that...
  6. Replies
    157
    Views
    10,658

    Neil, the max unemployment thru State of NH is...

    Neil, the max unemployment thru State of NH is around $427 (IIRC), that money is paid by employers thru a tax of payable wages. The extra $600 fed money is kicked in from the Cares Act and does not...
  7. Replies
    254
    Views
    32,961

    I’ll second this.......I have the full boat with...

    I’ll second this.......I have the full boat with them (gen liability, product liability, work comp, truck and building)
  8. Replies
    11
    Views
    1,251

    PM sent............ Thx Jim, Gottem;)

    PM sent............

    Thx Jim, Gottem;)
  9. Replies
    11
    Views
    1,251

    I’m interested too in some documentation. I...

    I’m interested too in some documentation. I picked up this Sharp mill with the same DRO, everything seems to work fine but there’s a “battery” indicator on the lower left in the front of display.
  10. Taxpayers Paid Millions to Design a Low-Cost...

    Taxpayers Paid Millions to Design a Low-Cost Ventilator for a Pandemic. Instead, the Company Is Selling Versions of It Overseas. — ProPublica

    I’m not sure why there hasn’t been much reporting on...
  11. 13k lb 26x120 lathe was my biggest with pinch bar...

    13k lb 26x120 lathe was my biggest with pinch bar and round bars, only had to move it 3’ so wasn’t too bad.
  12. Replies
    14
    Views
    1,346

    Lol......ya mean like this 20” 283363

    Lol......ya mean like this 20”

    283363
  13. (sorry didn’t proofread my post earlier)

    (sorry didn’t proofread my post earlier)
  14. Wouldn’t hurt, most use AW32 in those systems...

    Wouldn’t hurt, most use AW32 in those systems (which is avail at tractor stores)
  15. If you have a suspect area of suction leak try to...

    If you have a suspect area of suction leak try to smear a glob over the area (shaft seal or tubing/hose) and see if the sound changes, it may help to locate a suction leak
  16. A worn shaft seal or suction leak (between pump...

    A worn shaft seal or suction leak (between pump and reservoir) can allow air to be sucked in (air entrainment) or a clogged suction strainer could be starving the pump (cavitation)
  17. And worse, the inside of a #4 crimp fitting...

    And worse, the inside of a #4 crimp fitting reduces it to around .125” ID through the nipple. After crimping some #4 ends can barely fit a .125” punch through.
  18. Years ago Blackhawk Automotive and Enerpac was...

    Years ago Blackhawk Automotive and Enerpac was owned by Applied Power. That bottle jack is an original 12ton Blackhawk 67229...
  19. If you strike out at your local places I could...

    If you strike out at your local places I could make up an adapter. Here’s a sample of my custom fittings (before TIG welding)282797
  20. Degrease and use 3M 5200 Marine adhesive/sealant...

    Degrease and use 3M 5200 Marine adhesive/sealant is what I would use.
  21. My Gates catalogs only show 4-4 or 6-6 in female...

    My Gates catalogs only show 4-4 or 6-6 in female and male hose ends. Likely you’ll be using adapters to make it happen. Why not just use #4 hose? It’ll be choked down at the fittings anyway.
  22. Aaahhh, but maybe he’s a 24\7 security guard?:D

    Aaahhh, but maybe he’s a 24\7 security guard?:D
  23. Replies
    25
    Views
    3,865

    A brother-in-law needed a chain saw......I...

    A brother-in-law needed a chain saw......I delivered it to him with a new chain and bar gassed up ready to go. He tries to start it and yanks the cord out of the saw. I fixed it on the tailgate of...
  24. Replies
    23
    Views
    2,830

    Thanx for the replies guys, I psyched on this...

    Thanx for the replies guys, I psyched on this machine but my newbie-ness has nothing to compare to :cloud9:

    I did see a serial plate that had 2012 year of mfg but I will ask the previous owner...
  25. Replies
    23
    Views
    2,830

    279144 Sorry for the sideways pic above:crazy:...

    279144

    Sorry for the sideways pic above:crazy:

    How often should these covers be removed for housekeeping?
Results 1 to 25 of 274
Page 1 of 11 1 2 3 4