Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Jdub63

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    8
    Views
    1,072

    I can’t provide any input, but I’m watching this...

    I can’t provide any input, but I’m watching this tread. I just bought one of these too, and I’m starting the cleanup too.
  2. Replies
    5
    Views
    398

    Thanks for the suggestion. So you had the rails...

    Thanks for the suggestion. So you had the rails perpendicular to the motor shaft?

    Jim
  3. Replies
    5
    Views
    398

    10EE Spindle Motor Mounting Options

    I'm almost to the point of installing the spindle motor and gearbox into my project 10EE. It's a 57 square dial but missing all the original WIAD components. After discussion with Monarch, they...
  4. Replies
    8
    Views
    527

    Check out the Four Ponds video, he shows wiring...

    Check out the Four Ponds video, he shows wiring the ELSR in part 16. He restored a modular.
  5. Replies
    8
    Views
    527

    This is the only diagram provided by Monarch. ...

    This is the only diagram provided by Monarch. Sorry for the bad copy.

    good luck,

    Jim
  6. Thanks, Jim

    Thanks,

    Jim
  7. Can you provide the part number of the boost...

    Can you provide the part number of the boost transformer you used in your setup?
  8. WTB Monarch 10EE Taper Attachment Bed Bracket

    Looking for a bed bracket for my taper attachment. I'm not interested in Ebay prices. If anyone is still casting, I would be interested in finishing it out.

    thanks,

    Jim
  9. Replies
    14
    Views
    1,143

    Good looking setup. Are those multifix holders...

    Good looking setup. Are those multifix holders (Create Tool) or another brand? What size are you using? I'm trying to decide to spend the extra money and go with PeWe Tools or save and go with the...
  10. Replies
    5
    Views
    599

    Thanks for the replies. I'm on the hunt for...

    Thanks for the replies.

    I'm on the hunt for a 5/16 24 street elbow. I think a 90 right out of the manifold would make up any lost line and would remove that severe radius on the line going into...
  11. Replies
    5
    Views
    599

    Couple of 10EE saddle rebuild questions

    I started tearing down my saddle today, but I ran into a couple of issues.

    1. The oil supply line is broken. Based on the attached picture, what is your thoughts on trimming up the end and...
  12. Replies
    8
    Views
    696

    I was only looking at the machined surfaces. I'll...

    I was only looking at the machined surfaces. I'll have a look at the rest of the part.
  13. Replies
    8
    Views
    696

    Ebay, I contacted several sellers that look like...

    Ebay, I contacted several sellers that look like they part them out. The first one (CI) wasn't listed but he set up a private listing for me to buy. The second was an auction.

    Shipping on both,...
  14. Replies
    8
    Views
    696

    That's exactly the information I was needing. ...

    That's exactly the information I was needing. Thanks.

    I couldn't find any serial numbers yet, but there are several layers of paint. I'll let you know if I find any. I did take pictures of the...
  15. Replies
    8
    Views
    696

    Tailstock end covers

    Both my 53 MG 10EE and my 57 WIAD 10EE were missing the end covers. Recently I’ve been able to find a couple of replacements, but they’re different design. One is cast iron and doesn’t have any...
  16. I also talked with the suggested rigger, he...

    I also talked with the suggested rigger, he sounded like he was doing a couple of jobs for a friend but really didn't want to do anything else. Kinda like, if customers would stop calling, I could...
  17. Done, looks like the same bidder got both the...

    Done, looks like the same bidder got both the 10EE and the 13EE, time to start drinking
  18. Anyone from PM bidding on this auction?

    Anyone from PM bidding on this auction?
  19. Replies
    31
    Views
    8,133

    Thanks Dave. I'll give them a call. I spoke...

    Thanks Dave. I'll give them a call. I spoke with Scott last week, that's when I discovered the pin and lever are a single piece. He said that they have a jig they use to set the depth of the...
  20. Replies
    31
    Views
    8,133

    Old thread, but good stuff. I'm repairing my...

    Old thread, but good stuff. I'm repairing my ELSR handle, but have a question, how "deep" is the detent pin? In this picture I have it set for around 3/16 of an inch. Once I determine the...
  21. Did anyone see the 10EE round dial in the same...

    Did anyone see the 10EE round dial in the same auction? Comes with a the Monarch collet cabinet. If anyone around the auction area wants to do some pickup and shipping let me know :).
    ...
  22. Replies
    13
    Views
    1,183

    Thanks Cal. As one of the new guys, I think this...

    Thanks Cal. As one of the new guys, I think this is a move in the right direction.
  23. Replies
    4
    Views
    535

    thanks, at least I know I can buy them new... ...

    thanks, at least I know I can buy them new... anyone have some used ones?
  24. Replies
    4
    Views
    535

    WTB: Sheldon Mill Arbor / B&S #9 taper

    I have a Sheldon Horizontal Mill that is currently fitted with a vertical head. I want to convert it back to a horizontal mill but I need some Brown and Sharp #9 taper arbors. Looking for either 1"...
  25. Replies
    30
    Views
    2,930

    This cleared it up. As stated, it's interesting...

    This cleared it up. As stated, it's interesting that Monarch designed the stop in the same casting as the threading knob, I was wrong in thinking the two were tied together in some way.

    Thanks...
Results 1 to 25 of 77
Page 1 of 4 1 2 3 4