Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: jdownie

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    8
    Views
    1,978

    Lowered to $300. Pick up.

    Lowered to $300. Pick up.
  2. Replies
    8
    Views
    1,978

    It is wrapped and strapped to a pallet, so I...

    It is wrapped and strapped to a pallet, so I could ship.
  3. Replies
    8
    Views
    1,978

    Benchmaster Horizontal Mill

    Selling a beautiful Benchmaster.

    I bought this and never did anything with it. Still wrapped for shipping.

    The original owner said: “Production model. 1" arbor. 1 hp 230 volt 3 phase motor...
  4. Replies
    22
    Views
    5,768

    I forwarded this thread to my girlfriend who...

    I forwarded this thread to my girlfriend who replied...

    "Ries has a point, I think!"

    then, after rereading the original post...

    "Wait! I didn't notice that they're FREE! Suck it Ries! Fire...
  5. Replies
    8
    Views
    1,285

    Reduced Again I want to move these by the end...

    Reduced Again

    I want to move these by the end of next week. Pick up both lathes for $390.
  6. Replies
    8
    Views
    1,285

    Drastically Reduced! I have two circa 1951,...

    Drastically Reduced!

    I have two circa 1951, ex-Bulova Schaublin 102 lathes. There are no crossslides or other tooling. Both have tailstocks, beds, one has the regular headstock, the other a geared...
  7. This benchtop CNC mill came out of a high tech...

    This benchtop CNC mill came out of a high tech facility and appears to have had little use, if any. The current base price on a similar machine (Super ProLIGHT 1000) is over $18,000. ...
  8. Replies
    2
    Views
    625

    I was assuming the buyer would be able to acquire...

    I was assuming the buyer would be able to acquire the needed pieces. The lathes take W20 collets, which sell on ebay for less than $5 a piece.
    ...
  9. Replies
    0
    Views
    751

    Okay, here it is: 2 Schaublin 102 lathes, ca...

    Okay, here it is: 2 Schaublin 102 lathes, ca 1951, Bulova factory. One has regular back-motor headstock, the other a back motor geeared unit. Beds are immaculate - scraping marks all the way down....
  10. Replies
    2
    Views
    625

    Okay, here it is: 2 Schaublin 102 lathes, ca...

    Okay, here it is: 2 Schaublin 102 lathes, ca 1951, Bulova factory. One has regular back-motor headstock, the other a back motor geeared unit. Beds are immaculate - scraping marks all the way down....
  11. Replies
    5
    Views
    748

    Where are you located?

    Where are you located?
  12. Replies
    8
    Views
    1,285

    Just a bump...

    Just a bump...
  13. Replies
    0
    Views
    880

    http://www.practicalmachinist.com/cgi-bin/ubbcgi/u...

    http://www.practicalmachinist.com/cgi-bin/ubbcgi/ultimatebb.cgi?ubb=get_topic&f=4&t=002867
  14. Replies
    8
    Views
    1,285

    I have two circa 1951, ex-Bulova Schaublin 102...

    I have two circa 1951, ex-Bulova Schaublin 102 lathes. There are no crossslides or other tooling. Both have tailstocks, beds, one has the regular headstock, the other a geared unit. Asking $375...
  15. Replies
    5
    Views
    6,023

    Thank you...to a beginner the field is rather...

    Thank you...to a beginner the field is rather overwhelming. Can you give a short list of brands that offer appropriate CNC routers?

    John
  16. Replies
    5
    Views
    6,023

    Hello, I am trying to focus my research for a...

    Hello,

    I am trying to focus my research for a CNC machine that is capable of machining complex shaped models, out of aluminum and resin. Occasionally I might use steel, but this would be rare. I...
  17. Replies
    14
    Views
    2,564

    I am a complete beginner to machine tools, as is...

    I am a complete beginner to machine tools, as is most likely obvious from my questions. I am very familiar with basic woodworking machinery. I have pertty good computer skills but in no way am I an...
  18. Replies
    14
    Views
    2,564

    In the used CNC realm, what models would get me...

    In the used CNC realm, what models would get me started on my research?

    Thanks

    John
  19. Replies
    14
    Views
    2,564

    ALL the NC stuff, even the steppers and the...

    ALL the NC stuff, even the steppers and the brackets? Oh well. I have seen some high-speed grinding heads for Moore jig bores. Do you happen to know if they will fit the 1 1/2?

    John
  20. Replies
    14
    Views
    2,564

    I am open as to brand but need a machine smaller...

    I am open as to brand but need a machine smaller than the typical Moore 2, or BP knee mill. I realize that the jig borer is not as efficient as a real mill, but may have some precision advantages. ...
  21. Replies
    14
    Views
    2,564

    I am wondering if anyone has pondered this...

    I am wondering if anyone has pondered this conversion. I was thinking about using it for 3 axis milling, for prototyping models. I do not need the travel of a BP.

    Bad idea? Good idea?

    TIA...
  22. And perhaps a little more ...

    And perhaps a little more

    http://cgi.ebay.com/atlas-milling-machine-MFB_W0QQitemZ5602716068QQcategoryZ26261QQrdZ1QQcmdZViewItem

    5602716068
  23. 102 Prices... Hi, still trying to get a sense...

    102 Prices...

    Hi, still trying to get a sense of what I should ask for the lathes. Is $500 for the plainhead, and $700 for the gearhead too much?

    Thanks

    John
  24. The tailstocks have wheels at the back that turn....

    The tailstocks have wheels at the back that turn. I am not sure of the size MT. The headstocks are both roller bearing, W20.
  25. My tailstocks are round, old style. Will they...

    My tailstocks are round, old style. Will they fit? The ebay seller wants to know how much I am asking. I have 2 lathes, headstocks (1 step pulley, 1 geared), tailstocks, beds. Not compounds or...
Results 1 to 25 of 31
Page 1 of 2 1 2