Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: rustytool

Page 1 of 43 1 2 3 4

Search: Search took 0.02 seconds.

  1. And proper attire for working at the lathe.1-1/2"...

    And proper attire for working at the lathe.1-1/2" Round 1045 Cold Drawn Steel Bar Stock Lathe Mill 12"+ Tool CNC Machining | eBay
  2. Here's a manual of heads K&T...

    Here's a manual of heads K&T made.http://vintagemachinery.org/pubs/2098/3418.pdf
  3. You take off the domed cover plate then thread in...

    You take off the domed cover plate then thread in a puller into the threads on the exposed end of the shaft to pull it out.
  4. Maybe something like this.McMaster-Carr...

    Maybe something like this.McMaster-Carr
  5. Probably. The tubes have a ring soldered on the...

    Probably. The tubes have a ring soldered on the inside like you see on the outside.
    The 2HL vertical I'm working on now has tubes that look just like yours or worse.
    They look cool and everything...
  6. The plate goes on the front of the saddle. The...

    The plate goes on the front of the saddle.
    The brass telescoping tubes get gunked up and when one binds up it gets ripped out instead of sliding.
  7. I wanted that dividing head. Glad it stayed with...

    I wanted that dividing head. Glad it stayed with your mill though, kinda.
    You never see them with more than one plate and the tailstock.
  8. If that was the one on eBay with the vertical...

    If that was the one on eBay with the vertical head and overarm support I think you did good.
  9. June, 1943 I'd pick it up under the base but you...

    June, 1943
    I'd pick it up under the base but you could sling it around the overarms.http://vintagemachinery.org/pubs/2098/6771.pdf
  10. Needing a functional mill without have to sort...

    Needing a functional mill without have to sort out a lot of problems that wouldn't have been the machine for you.
    I already have a functional mill, that's why I picked up my 2HL vertical. It's going...
  11. Replies
    52
    Views
    3,277

    https://www.ebay.com/str/superiorworkholding

    https://www.ebay.com/str/superiorworkholding
  12. I've shown my Rivett before but here it is again....

    I've shown my Rivett before but here it is again.
    Shellac on the headstock and tailstock. The rest I just wipe down with an oily rag once in a while.
    It's not for everyone but I love it.
    I'm...
  13. Replies
    11
    Views
    777

    Looks like my 32" Sidney. But then again they...

    Looks like my 32" Sidney.
    But then again they all look alike.258866258867
  14. Replies
    36
    Views
    3,046

    It's a wrench to open a can of spam.

    It's a wrench to open a can of spam.
  15. Replies
    16
    Views
    1,591

    The Rivett 1020S has 19 tip.

    The Rivett 1020S has 19 tip.
  16. Replies
    21
    Views
    1,604

    My 2009 Ford Ranger has 27,000 miles on it. I...

    My 2009 Ford Ranger has 27,000 miles on it.
    I never drive.
  17. I have both, the Rivett 6r collets and Hardinge...

    I have both, the Rivett 6r collets and Hardinge 6h collets.
    Both work. The Hardinge are a little shorter and don't stick out of the spindle nose as far.
    Some of the Rivett ones besides being marked...
  18. Replies
    14
    Views
    1,221

    Rust protection and on electrical connections....

    Rust protection and on electrical connections.
    Lubrication of bicycle chain. Applied at the start of last winter and after riding for months in the rain and snow there was no rust visible on the...
  19. My manual shows the D1-4 spindle with a 5mt bore....

    My manual shows the D1-4 spindle with a 5mt bore.
    The D1-4 has a spindle through hole of 1-3/8 versus the 1-1/4 through hole of the L0 spindle.
  20. Replies
    14
    Views
    1,221

    I use Corrosion X and like it better than...

    I use Corrosion X and like it better than anything else I've tried.
  21. Ditch the jeans and wear sweat pants.

    Ditch the jeans and wear sweat pants.
  22. Replies
    26
    Views
    1,778

    For the same reason I always had my bicycle in...

    For the same reason I always had my bicycle in the back of my '66 VW bus.
    Just in case.
  23. His repair stands are really nice. Member...

    His repair stands are really nice.
    Member rockcombo has 2 in his shop.
    Efficient Velo Tools (EVT)
  24. Someone in Idaho bought a Rivett that was for...

    Someone in Idaho bought a Rivett that was for sale in Seattle. Think the seller was on here.
    Maybe it is the same one. Too bad the youtube guys are too good to hang out here.
  25. Does the disc running dry or in an oil bath (my...

    Does the disc running dry or in an oil bath (my situation) make a difference in material choice ?
Results 1 to 25 of 1057
Page 1 of 43 1 2 3 4