Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: carbonbl

Page 1 of 11 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    711

    I had a similar problem and solved it by lowering...

    I had a similar problem and solved it by lowering the baud rate a little. That was with a machine with -2 boards, so YMMV.
  2. Replies
    12
    Views
    1,636

    Another vote for an older Mazak with Mazatrol. I...

    Another vote for an older Mazak with Mazatrol. I have an '89 QT8 with T32-2 control, love mazatrol for the simple parts I do. Parts, parameters and manuals are available from Mazak (not cheap, but...
  3. Replies
    42
    Views
    4,576

    My '84 I posted about earlier is still going...

    My '84 I posted about earlier is still going strong, but at times I really want a full enclosure and a faster control. I can't really envision anything from another manufacturer under $10k-$15k that...
  4. Replies
    2
    Views
    797

    Can you get a tool number to show up if you...

    Can you get a tool number to show up if you manually command a tool change with "TC,1"?
  5. Replies
    37
    Views
    2,833

    Touch off tool on 4" block (or whatever your tool...

    Touch off tool on 4" block (or whatever your tool setting reference is). Take note of Z value, let's call this Z1.

    Touch off tool on desired Z0 for your fixture offset. Take note of this Z value...
  6. Replies
    8
    Views
    1,298

    Perhaps a component of some vacuum workholding...

    Perhaps a component of some vacuum workholding system?
  7. That seems significantly better than the...

    That seems significantly better than the materials I mentioned. I will look into this, thank you!
  8. Any print on demand services offering Nylon 6 for SLS printing?

    I have a product family that I've prototyped in PA2200/PA12 Nylons, but would really benefit from the increased heat resistance of Nylon 6. I found a couple press release-type articles stating that a...
  9. I sent these guys a ballscrew from my Mazak for...

    I sent these guys a ballscrew from my Mazak for rebuild, IIRC based on recommendations here on PM. Unsuprisingly, it was too far gone for rebuilding (very abused machine I resurrected) but they were...
  10. Replies
    20
    Views
    1,633

    Seconding D Nelson's suggestion. Because Fadal...

    Seconding D Nelson's suggestion. Because Fadal naming conventions are so limited and onboard memory usually fairly small I don't bother with any organizational scheme for files that are in machine...
  11. Clarifying for the OP, very few Fadals had Fanuc...

    Clarifying for the OP, very few Fadals had Fanuc control hardware. I think it's best to avoid those. Fadals with CNC88 or 88HS control hardware are very easy from the service side, all control...
  12. Replies
    37
    Views
    2,833

    H0 does the same thing as G49, tool offset...

    H0 does the same thing as G49, tool offset cancel. This might be a format 2 quirk, never needed this on a format 1 machine.
  13. Replies
    22
    Views
    2,672

    If cutting dry, route a shop vac near the cutting...

    If cutting dry, route a shop vac near the cutting tool...suck up the chips before they go everywhere. 2.5" Loc-line works great.
  14. Replies
    37
    Views
    2,833

    Yes that is correct. My method, Perry's, kazlx's...

    Yes that is correct. My method, Perry's, kazlx's and the tool setting routine are all doing essentially the same thing in this regard, just using slightly different procedures.
  15. Replies
    37
    Views
    2,833

    It's fine unless for some reason you have changed...

    It's fine unless for some reason you have changed the default home position on your Fadal to some weird spot. I know some people do this but why I will never understand, the default home position on...
  16. Replies
    37
    Views
    2,833

    It's pretty simple and mostly done out of force...

    It's pretty simple and mostly done out of force of habit since when I learned how to run my Fadal when it had early version control boards with no toolsetter utility.

    Load tools into carousel and...
  17. Replies
    37
    Views
    2,833

    Fadal Z0 with no offset active is the toolchange...

    Fadal Z0 with no offset active is the toolchange position. Well above where anything bad could happen.
  18. Replies
    37
    Views
    2,833

    If you're setting your tools using a 4" block and...

    If you're setting your tools using a 4" block and using the tool setting routine, you should be entering a 4" Z fixture offset in the setting routine and the Z value for E1 should be zero. This is...
  19. Replies
    37
    Views
    2,833

    How are you setting your tool and fixture offsets...

    How are you setting your tool and fixture offsets though?
  20. FYI for those of you that are having issues with...

    FYI for those of you that are having issues with getting the HSMWorks license to activate, Autodesk just released an update to solve this issue. This has fixed my problem where HSMWorks would not...
  21. This is awesome, thanks for the heads up. I use...

    This is awesome, thanks for the heads up. I use HSMXpress supplemented with Fusion360 for 3D toolpaths and this will simplify my workflow greatly.
  22. Replies
    4
    Views
    851

    Take all this with a grain of salt as I don't...

    Take all this with a grain of salt as I don't have your machine but I do have a QT8 made around the same time. Looking up your machine it appears to be of a similar configuration.
    Mine had an...
  23. I'm sorry, I don't really understand your...

    I'm sorry, I don't really understand your situation. You're borrowing a lathe but the lender won't let you use it to make your own parts?
    If you're not able practice at a slow and deliberate pace,...
  24. BUMP...I'm really surprised no one has any...

    BUMP...I'm really surprised no one has any insight on this!
  25. Best practices for evaluating condition of used hydraulic chuck?

    Say I want to look at a used Kitagawa hydraulic three-jaw chuck at an auction or used machinery dealer. I've really only dealt with hydraulic chucks installed on machines under power, so not sure...
Results 1 to 25 of 275
Page 1 of 11 1 2 3 4