Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: cj7jeep81

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    10
    Views
    553

    If you mean the brown rectangular thing, here are...

    If you mean the brown rectangular thing, here are the right and left side. First pic is the left side, second pic is the right side.
  2. Replies
    7
    Views
    207

    I just spent a good bit of time trying to figure...

    I just spent a good bit of time trying to figure something similar out, for a machine that weight about the same. I don't think you can get away from paying the $500 to get it loaded by the auction...
  3. Replies
    10
    Views
    553

    Yeah, that's pretty close. Here is my panel. ...

    Yeah, that's pretty close. Here is my panel. Not sure why its so small, but second one is a bit bigger.
  4. Replies
    10
    Views
    553

    Yep, you are exactly correct. My biggest concern...

    Yep, you are exactly correct. My biggest concern with rewiring my mill controls is I really don't have a lot of experience with control circuits and that type of thing, and the wiring isn't all that...
  5. Replies
    10
    Views
    553

    Planning on getting something like this. Will...

    Planning on getting something like this. Will take 240 from my 3 phase panel through this, and feed the machine.
    3 kVA-75 kVA 3 Phase Transformers: 480-240-Volt | NAPCco
  6. Replies
    10
    Views
    553

    Thanks, right now, I'm looking to see if I can...

    Thanks, right now, I'm looking to see if I can find a transformer fairly cheap, and use that to test the machine out. If I can't find one, I'll start looking at what you mentioned. The wiring...
  7. Replies
    10
    Views
    553

    Series II Bridgeport electrical diagrams

    I recently purchased a series 2 bridgeport at an auction. It had a label on the panel that it was 480v, and I confirmed the wiring in the spindle motor was wired up for high voltage. I do not have...
  8. Replies
    26
    Views
    1,908

    Thanks everyone for the information, and...

    Thanks everyone for the information, and hopefully I'll be able to use it in the future. Unfortunately, the price went higher than I could justify, so no VMC for me yet. But I did get a 6x18 fully...
  9. Replies
    26
    Views
    1,908

    Thanks for the replies everyone, if I end up with...

    Thanks for the replies everyone, if I end up with it, I'm sure I'll try a few of these methods, and will not be in any hurry at all. Will definitely sweep the floor multiple times prior/during the...
  10. Replies
    26
    Views
    1,908

    Thanks for the feedback. Trailer I'm looking at...

    Thanks for the feedback. Trailer I'm looking at is power tilt, and rated for 11 or 12k payload. Agreed it wouldn't be a good place to learn how to use skates, so hope to use riggers.
  11. Replies
    26
    Views
    1,908

    Yeah, unfortunately this is a bit outside of the...

    Yeah, unfortunately this is a bit outside of the walk behinds I've seen, or too close for comfort. So here is my total plan, and based on the recommendations for more affordable skates, I might be...
  12. Replies
    26
    Views
    1,908

    Thanks! The machine I'm looking at is 8,500...

    Thanks! The machine I'm looking at is 8,500 pounds, so a bit lighter than your brake. Not sure if I'll have an anchor point to pull from though when moving into my shop. Worst case, I could drill...
  13. Replies
    26
    Views
    1,908

    Thanks, I've thought about that as well. I had...

    Thanks, I've thought about that as well. I had only really seen the big Hillman skates for sale before, and those were well out of my budget (and way bigger than I need). However, I see these on...
  14. Replies
    26
    Views
    1,908

    Yeah, up until this point the heaviest stuff I've...

    Yeah, up until this point the heaviest stuff I've had to move is 4,000lbs, which can be handled easily with my pallet jacks. Guess if I'm going to get into bigger machinery, I better upgrade my...
  15. Replies
    26
    Views
    1,908

    Moving VMC with pallet jacks

    I am looking for a VMC for my home shop, and am trying to figure out how to move it whenever I get one. One model I'm looking at is the Fadal 3016, so figure something around that size and weight...
  16. Replies
    8
    Views
    1,171

    Yeah, I might be out of luck, thanks for the info!

    Yeah, I might be out of luck, thanks for the info!
  17. Replies
    8
    Views
    1,171

    Couldn't find that model on their site, and like...

    Couldn't find that model on their site, and like I said I emailed them a week or two ago, and no response.
  18. Replies
    8
    Views
    1,171

    Of course, shortly after posting I find some...

    Of course, shortly after posting I find some stuff that makes me think they are CDE inserts, right hand, and I'm guessing 322 for the smaller ones, and 422 for the bigger.
  19. Replies
    8
    Views
    1,171

    Resource to identify carbide insert?

    I got an Ingersoll Rand max-i-cut 2" indexable endmill at an auction with a bunch of other stuff I wanted, but several of the inserts are chipped. I've searched and found nothing, and emailed...
  20. Replies
    4
    Views
    927

    Made good progress on machining a new handle, but...

    Made good progress on machining a new handle, but have a question. It looks like a previous owner repaired the knobs the handles engage. Anyone know if these are in the stock location? It doesn't...
  21. Replies
    4
    Views
    927

    Unfortunately I don't have an oxy/acetylyne...

    Unfortunately I don't have an oxy/acetylyne setup, so no brazing for me. I plan on using aluminum bronze or silicone bronze filler wire, so more of a tig brazing then welding I suppose.
  22. Replies
    4
    Views
    927

    Source for handles for 12" CK

    Well, one of the handles for my 12" CK finally broke last night, right where a previous owner had attempted to weld it back together. I have all the pieces, and will see if I can tig it back...
  23. Replies
    1
    Views
    2,109

    Bumping an old thread, but I have an 8" 4 jaw,...

    Bumping an old thread, but I have an 8" 4 jaw, and this thread is the only thing I've been able to find on the internet, and would also like to know if anyone has any info on them.
  24. Replies
    0
    Views
    595

    Replacing pulley/sheave on Monarch CK

    I'm getting most of my parts together to replace the motor on my Monarch CK. Top speed is only 550 RPM, and I'd like to double that. Motor that is in there is an original 5hp motor, that spins...
  25. I'll try that, thanks!

    I'll try that, thanks!
Results 1 to 25 of 102
Page 1 of 5 1 2 3 4