Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: rpseguin

Page 1 of 41 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    4
    Views
    1,720

    Time for me to yet again awaken an old thread! ...

    Time for me to yet again awaken an old thread!

    Can you please share scans and insights on doing the conversion of A1-6 chucks et al to D1-6?

    I'm hoping to get a D1-6 spindle to swap out my A1-6
  2. Wow! That is a good deal! I keep looking for a...

    Wow! That is a good deal!
    I keep looking for a 6 jaw chuck with reversible top jaws, 5" or 6" with a Hardinge 4 degree taper lock mount on it.
  3. Hmmm... I don't have a surface grinder, but...

    Hmmm...
    I don't have a surface grinder, but have been wanting to get one for a long time. I don't have much space to fit one.
    I don't know if a mill would give an acceptable
    face tolerance...
  4. Replacing old 1 piece chuck jaws with 2 piece reversible jaws?

    Does anybody make 2 piece reversible jaw sets for some of the more common older chucks?
    I have a couple of Buck 3 jaw chucks with single piece jaws where I'd like to replace the single piece jaws...
  5. Thanks for the tip! Looks interesting. I...

    Thanks for the tip!
    Looks interesting.
    I contacted them for more details.
    1.3Ē diam spindle thru hole is smaller than Iíd prefer.
    It looks like an L1 spindle nose, which is definitely better than...
  6. Nice!! Iím jealous! Iím wondering about my...

    Nice!!
    Iím jealous!

    Iím wondering about my not so great concrete garage floor which already has a few cracks in it.
    If I could make machinery levitate, I could redo the whole floor with...
  7. Replies
    21
    Views
    1,619

    What is the spindle bore/thru hole size? Max...

    What is the spindle bore/thru hole size?
    Max RPM?

    Beautiful lathe!
  8. Replies
    21
    Views
    1,619

    That lathe looks very nice!! Congratulations!! ...

    That lathe looks very nice!!
    Congratulations!!
    Thatís about the size Iím looking for too!
    I might have to add Hendey to my list!
    What is the spindle thru hole size?
    Max spindle speed?
  9. Replies
    4
    Views
    335

    All the HLV-H cabinets Iíve seen have 4 feet. ...

    All the HLV-H cabinets Iíve seen have 4 feet.

    For Hardinge , the 3 point kinematic mount is the bed/frame casting mount interface to the cabinet.
  10. Replies
    3
    Views
    186

    Monarch Lathes, L.P. Phone: 937-492-4111 Fax: ...

    Monarch Lathes, L.P.
    Phone: 937-492-4111
    Fax: 937-492-7958
    Email: [email protected]
  11. Replies
    10
    Views
    410

    Thatís affirmative! Open to suggestions!

    Thatís affirmative!
    Open to suggestions!
  12. Replies
    10
    Views
    410

    Yeah. Gonna block & report his phone #...

    Yeah. Gonna block & report his phone # (615-908-5671) and email ([email protected])

    I will refrain from posting my email address. I just wish messaging on PM wasnít so bad!

    Iím...
  13. Replies
    10
    Views
    410

    And, a quick web search for Webb Whacheon WL-435...

    And, a quick web search for Webb Whacheon WL-435 lathe spindle ďshockinglyĒ shows some of the same pictures this person is texting to me.

    Le sigh!
    I was hoping I had found a good deal on a D1-6...
  14. Replies
    10
    Views
    410

    WTB: D1-6 spindle for Webb/Whacheon Lathe

    Iíve edited the original post and removed my email since someone (ďEddieĒ) is apparently trying to scam me.

    Weíve been texting back and forth a little bit.
    He really wants me to pay with family...
  15. That sounds like you got a good deal, especially...

    That sounds like you got a good deal, especially for NOS!
    Anyhow, I could do $30/set for those + $8 for flat rate shipping.
  16. Replies
    10
    Views
    410

    WTB: D1-6 spindle for Webb/Whacheon Lathe

    If you know someone that has a D1-6 spindle or headstock for a 1980s Whacheon/Webb/Mori Seiki, please contact me

    Thanks!
  17. Suggestions on asking prices?

    Suggestions on asking prices?
  18. Interesting points. Iím also space constrained....

    Interesting points.
    Iím also space constrained. Most of the tracer attachments Iíve seen take up a lot more space.
    Iíve never used a tracer before, so Iím wondering how temperamental they are.
    ...
  19. Thanks for your response! I've always...

    Thanks for your response!




    I've always heard good things about Mori manual lathes, so it is interesting to hear the contrast with American iron.
    I have a Webb, and it is a good lathe, but my...
  20. Replies
    30
    Views
    1,332

    I agree. Remove as much as possible and lighten...

    I agree. Remove as much as possible and lighten it up.
    The carriage is probably tilting and wedging
    Tear it all down first, most of which is covered in the maintenance manual.
  21. Replies
    30
    Views
    1,332

    I believe Hardinge would paint them whatever...

    I believe Hardinge would paint them whatever color the customer wanted.

    Thanks for posting so many detailed pics and info!!
    This will be useful for people in the future!
  22. Thread: Buying a used

    by rpseguin
    Replies
    4
    Views
    485

    Suggest better title to the thread: "Buying from...

    Suggest better title to the thread: "Buying from Machineinventory.shop?"
  23. Hardinge Precision Leadscrews + Followers

    Time for me to thin out and make space!
    How much are Hardinge precision leadscrews and followers worth?

    I have the following Hardinge precision leadscrews and followers for Hardinge HC, HCT,...
  24. Thanks! Iíve been browsing ebay and elsewhere...

    Thanks!
    Iíve been browsing ebay and elsewhere looking at various machines including Monarch series 62, some L&S and Axelson, ...
    Some of the ways on some of them donít look great with grooves,...
  25. Yes, Iím reviving an old thread again... That...

    Yes, Iím reviving an old thread again...

    That Starrett Government micrometer set is cool and I hadnít seen one before.

    Hereís a Starrett micrometer a friend gave me that I thought was...
Results 1 to 25 of 1013
Page 1 of 41 1 2 3 4