Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: BrianB

Page 1 of 21 1 2 3 4

Search: Search took 0.01 seconds.

  1. My #4 machine is 25hp on the main spindle 7.5 on...

    My #4 machine is 25hp on the main spindle 7.5 on the independent overarm.
  2. Replies
    4
    Views
    966

    My Carlton has the spindle nose made like my G&L...

    My Carlton has the spindle nose made like my G&L it is designed for MT tooling that had flats on each side for delivering torque much like how a mill spindle keys works. This kept from shearing the...
  3. Replies
    37
    Views
    5,506

    What are the travels? What are the feed rates on...

    What are the travels? What are the feed rates on the facing slide?
  4. Replies
    188
    Views
    29,058

    So I have my saddle and cross slide back from the...

    So I have my saddle and cross slide back from the machinist. I'm measuring up to get the best Rulon 143 installation strategy mapped out for the next step.

    [/QUOTE]

    Just glue the Rulon on...
  5. Replies
    15
    Views
    2,037

    I would think that is a lot of slant over a small...

    I would think that is a lot of slant over a small distance. I would aim to correct it.
  6. Replies
    24
    Views
    4,544

    I haven a 20x96 Monarch and a 40x180 so longer...

    I haven a 20x96 Monarch and a 40x180 so longer ones do exist, just have to keep your eye out. That being said I rarely ever go more than 36" out from the chuck on my 96" machine.
  7. Replies
    2
    Views
    961

    I have a CBB lathe. it appears extensively on my...

    I have a CBB lathe. it appears extensively on my you tube channel. YouTube
  8. Replies
    3
    Views
    1,524

    The other video is up. YouTube...

    The other video is up. YouTube
  9. Replies
    3
    Views
    1,524

    That old plate has been well stoned and all that...

    That old plate has been well stoned and all that is left is the rust stains in the low scraped spots. It actually is not too bad. It is plenty good for figuring out what way things are going which is...
  10. Replies
    3
    Views
    1,524

    Machine Tool Remachining

    I recut the surfaces on a Monarch lathe carriage and cross slide to remove scoring and wear and reestablish alignments as per the factory as best as I could follow. I shot video of all of it and...
  11. Replies
    15
    Views
    2,465

    You could weld and remachine using the right...

    You could weld and remachine using the right methods but it likely would distort and have to have other adjustments made after the process. You could also machine off the tops of the T and bolt on...
  12. Replies
    12
    Views
    2,507

    Awesome read, plenty of determination and yeah we...

    Awesome read, plenty of determination and yeah we can do that. :-)
  13. This video series on my G&L adventures might help...

    This video series on my G&L adventures might help you. YouTube

    I must have done ok on it as when I milled a shaper body on it and they checked it on a CMM I had all the surfaces over 4feet in each...
  14. I have one that is identical to it except with...

    I have one that is identical to it except with different face guards.
  15. Replies
    31
    Views
    6,868

    Does it have the side head? I might be interested...

    Does it have the side head? I might be interested in it. Can you send me some pictures to bcbloc02 at yahoo dot com?
    Thanks
    Brian
  16. If you notice in my you tube videos using the HBM...

    If you notice in my you tube videos using the HBM I almost always use stop blocks and I usually try to place my hold down bolts so they block too so the part has physical stops in every direction....
  17. Replies
    25
    Views
    5,198

    Looks like typical locomotive type construction...

    Looks like typical locomotive type construction where the tubes are rolled over into the flanges, but I imagine that is pretty standard to all tube boilers. That cross section appears to be all mild...
  18. Replies
    25
    Views
    5,198

    There are some pictures and a vaguely detailed...

    There are some pictures and a vaguely detailed description of the riverboat boiler setup in the ASME paper.
    ...
  19. Replies
    25
    Views
    5,198

    Thanks for the insightful reply. I do know that...

    Thanks for the insightful reply. I do know that the Belle uses a sediment tank under the boilers to feed the 3 boilers then there is a collection system on top. I talked to the fireman and when they...
  20. Replies
    25
    Views
    5,198

    I recently did a video on the steamboat Belle of...

    I recently did a video on the steamboat Belle of Louisville YouTube I found it interesting that they were still using river water in the boilers. I assume no real treatment of any value could be done...
  21. Replies
    30
    Views
    6,129

    Maybe by next year I will have my shop setup...

    Maybe by next year I will have my shop setup where I could host a class. Lots of work to do before then still!!
  22. Replies
    423
    Views
    84,362

    I can't say for sure but are you certain you have...

    I can't say for sure but are you certain you have the oil level right? My G&L 340T only has about 2inches deep of oil in the headstock.
  23. Replies
    10
    Views
    1,538

    I could probably mill it to within .002" or less...

    I could probably mill it to within .002" or less over the length on all dimensions on my HBM. I am just over an hour south of Cincinnati.
  24. Maybe I missed out? Anyway I sent you a PM reply,...

    Maybe I missed out? Anyway I sent you a PM reply, I just hadn't been on here since my last post and for some reason don't seem to get email notifications when there is activity in my PM box.
  25. My series 90 has a 4.25" bore so I know they did....

    My series 90 has a 4.25" bore so I know they did. I think the 612 and 62 series were 2-1/16"
Results 1 to 25 of 514
Page 1 of 21 1 2 3 4