Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: johnoder

Page 1 of 60 1 2 3 4

Search: Search took 0.16 seconds; generated 2 minute(s) ago.

  1. Amazing - thanks for sharing that I wondered...

    Amazing - thanks for sharing that

    I wondered what the BIG dia. was in the other photo

    Might be a plan to just adapt a ER40mm collet holder to that big flange

    279174
  2. Replies
    9
    Views
    428

    Not quite 11 MB headed your way Weight and...

    Not quite 11 MB headed your way

    Weight and size guesses

    About 5200 Lbs

    About 11 feet long
  3. Sort of in the K&T category - that PATENTED the...

    Sort of in the K&T category - that PATENTED the flanged and face keyed spindle nose in 1913 - which was later incorporated into the NMTB design not quite twenty years later

    279171

    I still would...
  4. Look at your photo again. Can we have a shot of...

    Look at your photo again. Can we have a shot of the spindle nose without any arbors stuck in there?
  5. I have to ask WHY all the B&S for a NMTB spindle?...

    I have to ask WHY all the B&S for a NMTB spindle?

    Your photo - I am assuming this is the one you ended up with (or did Hendey actually put a 10 B&S hole in the middle of this "modern" design?)
    ...
  6. Not correct, image is not for 9 B&S Standard...

    Not correct, image is not for 9 B&S

    Standard tapers

    Standard Tapers


    VME has 9, not 10 B&S collets

    Years ago Grand Tool in NJ sold them - might want to contact them
  7. Don't recall. I think it went to scrap in the...

    Don't recall. I think it went to scrap in the nineties

    Dual voltage can be "reconnected" for lower volts (in the "pecker head" on the motor itself), and appropriate KVA transformers can take care...
  8. The 24" rotary table feeds left or right...

    The 24" rotary table feeds left or right rotation. It is mounted in a saddle assy that feeds 25" in and out on the machine base and 25" side to side on the upper portion of the saddle assy.

    This...
  9. I'll suppose later - I do know there were earlier...

    I'll suppose later - I do know there were earlier versions of the vertical shaper - as in Accuracy For Seventy Years from 1930. Here is a link to that pub
    ...
  10. Stuff like built in powered rotary table and...

    Stuff like built in powered rotary table and tilting ram - and a way better view of what you are doing

    "Turning and boring" on mine

    279067279068279069
  11. Replies
    14
    Views
    4,305

    Probably would have heard of it if there was such...

    Probably would have heard of it if there was such a thing:D

    Post the serial and I'll see if I can date it
  12. Replies
    14
    Views
    4,353

    Bobby - if you are referring to user name...

    Bobby - if you are referring to user name widlin1, he was last on the forum a year ago, but you could click on that name and send him an email and see if he responds to same. Maybe he has a link to...
  13. If a 50 NMTB spindle nose, make that part fit...

    If a 50 NMTB spindle nose, make that part fit OVER the 5.0625" O.D. of that spindle nose - even if just a short "snap" fit

    Then every time you put it on it will run true
  14. Several here, older of course from this 1911 pub....

    Several here, older of course from this 1911 pub.

    Starting on page 184

    Precision tools : Pratt & Whitney Company : Free Download, Borrow, and Streaming : Internet Archive
  15. Replies
    18
    Views
    956

    As can be seen by the hump on the QC gearbox,...

    As can be seen by the hump on the QC gearbox, this Monarch has Lead Screw Reverse on the apron - maybe its all there and still works. Lever is way up high on right end of apron
  16. I'll see if some progress can be made on scanning...

    I'll see if some progress can be made on scanning these today. PM arrived, thanks

    On Edit: A bit less than 3Mb emailed
  17. Replies
    6
    Views
    458

    Made in '43, almost no info at VM Springfield...

    Made in '43, almost no info at VM

    Springfield Machine Tool Co. - Publication Reprints | VintageMachinery.org

    ph
  18. D1-2" tooling here - along with another lathe ...

    D1-2" tooling here - along with another lathe

    Pratt & Whitney Model C collet Lathe - tools - by owner - sale

    Not very close of course - but this sort of stuff is where ever it is - and it needs...
  19. Weights here from 1923 Cincinnati. I would not...

    Weights here from 1923 Cincinnati. I would not expect the asked for Dividing Heads to be heavier

    278818

    The weights shown of course include the related brackets and gearing to drive the...
  20. Replies
    4
    Views
    269

    Total loss they call it. I expect a few were...

    Total loss they call it. I expect a few were turned off over night, but only if the BULL made it plain that was expected. There were low pay folks hired as wipers to clean up the mess now and then...
  21. Post #2 says they are available :D I'll have...

    Post #2 says they are available :D

    I'll have to scan them, then I'll need you to private message me your email address

    S/N 688 is about 1943

    Made here - a neat place long gone
    ...
  22. You could answer this question - if varying...

    You could answer this question - if varying thickness you need a ball shaped cutter possibly

    278786
  23. Replies
    12
    Views
    578

    Great stuff from long ago in that category ...

    Great stuff from long ago in that category

    http://vintagemachinery.org/pubs/1617/5795.pdf

    A treatise on milling and milling machines .. : Cincinnati Milling Machine Company : Free Download,...
  24. Thanks to me :D and ASA/ASME B5.9 Spindle Noses

    Thanks to me :D and ASA/ASME B5.9 Spindle Noses
  25. Replies
    18
    Views
    956

    It means the Monarch was built in 1942 (serial...

    It means the Monarch was built in 1942 (serial 13626)

    The "restamp" (on the Bronze tag) suggests to me that a seller was trying to make it "younger" at some point in its life

    Monarch may be...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4