Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Phil in Montana

Page 1 of 33 1 2 3 4

Search: Search took 0.01 seconds.

  1. With the cheap prices on fiber scopes nowadays,...

    With the cheap prices on fiber scopes nowadays, look inside for rust pits, and hydro, your tank might be just fine...Phil
  2. I received the 4 dolly's today, weldaments are...

    I received the 4 dolly's today, weldaments are very good, Bearings are small, plastic on wheels not much will probably fail, but for 35 bucks each and free shipping ok deal.I couldn't build the...
  3. Even one 10 years old will light years better...

    Even one 10 years old will light years better that a 72 clark...Just find a newer one with a good battery, the cost of a NEW fork will or should scare you...Phil
  4. The rods are needed, you will need to find...

    The rods are needed, you will need to find another way to store your goods...Phil
  5. A fuse has been installed, so they want a path to...

    A fuse has been installed, so they want a path to ground to pop the fuse...Phil
  6. Replies
    4
    Views
    256

    It has a electronic start control, go on line and...

    It has a electronic start control, go on line and find a wiring dig. for it...Phil
  7. 1950 NEC, now it is required to be grounded...Phil

    1950 NEC, now it is required to be grounded...Phil
  8. What about cutting one end off and sliding a new...

    What about cutting one end off and sliding a new smaller tank inside?...Phil
  9. I used to test tanks for MSHA, Scrap the damm...

    I used to test tanks for MSHA, Scrap the damm thing, the test would look for any changes on the tank, (welds) hydro to tag specks,( every ASME tank would have the specs and date of mfg) Used...
  10. get a diesel generator then..Phil

    get a diesel generator then..Phil
  11. A 200 amp service will not power a 25hp rpc, at...

    A 200 amp service will not power a 25hp rpc, at 60 hp it time to pucker up buy 3 phase and pay the bill, or get a 75kw diesel generator ( your hoa will love that)...Phil
  12. Replies
    45
    Views
    2,222

    No but there is no need to have it filtered, and...

    No but there is no need to have it filtered, and at a 20+ amp draw it would be a huge filter caps, with one hell of inrush amps, you would need 200 amp didoes to hold the current, so I would think no...
  13. Replies
    45
    Views
    2,222

    JST is right, unfiltered the dc will be the 240...

    JST is right, unfiltered the dc will be the 240 volt less 1.4 volts for loss in the didoes....It does get a little tricky if there is no load on the motor, it will act as a filter and the voltage...
  14. Replies
    45
    Views
    2,222

    In my motor shop we would use a thinned hacksaw...

    In my motor shop we would use a thinned hacksaw blade to clean the slots if we didnt have to turn and undercut the comm, it cleans the slot quickly and didnt require a great amount of skill set...In...
  15. You need to get into your menu and make some...

    You need to get into your menu and make some other adjustments, v/hz and others to calm your motor down...Phil
  16. In box is now empty, Send me a note what you want...

    In box is now empty, Send me a note what you want in make you a deal you cant refuse...Phil
  17. Replies
    45
    Views
    2,222

    Ring of fire was no/bad brush contact,no power...

    Ring of fire was no/bad brush contact,no power was the same problem... grind the sides of the saw blade so there is no rake to the teeth...Phil
  18. Look close 480 volt...Phil

    Look close 480 volt...Phil
  19. Replies
    45
    Views
    2,222

    You have a cleaning job to do, free the brushes,...

    You have a cleaning job to do, free the brushes, de grease the comm, (the copper thing with the slots), and clean the slots...surf the web for info, then ask here for help...you should remove the...
  20. Maybe, someone has made a adptr to fit a larger...

    Maybe, someone has made a adptr to fit a larger lathe already...Phil
  21. I have used them to run a belt drive hydro pump,...

    I have used them to run a belt drive hydro pump, about 5hp at 1800, worked for years...Phil
  22. Replies
    5
    Views
    459

    Indexer from a B&S grinder...Phil

    Indexer from a B&S grinder...Phil
  23. I dont see how he is making any profit on them,...

    I dont see how he is making any profit on them, 12 bearings at 2 bucks each, 3 bolts and nuts at 4 bucks and a 3 dollar piece of channel, and paint about 40 bucks in parts...Phil
  24. Been there done that.. not easy...It is important...

    Been there done that.. not easy...It is important that the tail stock ram is bored straight and true..I dont know any other way unless you have a chucking grinder...Phil
  25. Replies
    13
    Views
    601

    I go on the sqr rule... 1/2 the speed is 1/4 the...

    I go on the sqr rule... 1/2 the speed is 1/4 the hp, it may not be textbook right but it works for me...Phil
Results 1 to 25 of 810
Page 1 of 33 1 2 3 4