Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Roooster

Page 1 of 16 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    47
    Views
    3,040

    Roeders? YouTube (https://youtu.be/1gXKPbD0lZs)

    Roeders?
    YouTube
  2. Replies
    74
    Views
    5,322

    You won’t have any problems, Kamil. Chances are,...

    You won’t have any problems, Kamil. Chances are, I’ll fit your probe.
  3. Replies
    74
    Views
    5,322

    Does the TS27 connect to an HSI interface?...

    Does the TS27 connect to an HSI interface? Without it, operation could be sketchy...
  4. Replies
    74
    Views
    5,322

    I still think it is a wiring issue with the fast...

    I still think it is a wiring issue with the fast probe input at TB4-31.
  5. Replies
    74
    Views
    5,322

    Has it been wired up correctly? There are two...

    Has it been wired up correctly? There are two ‘fast’ probing inputs at TB4-30 & 31 that if they are not present or transposed, will cause issues. If the control parameters are incorrect, it may cause...
  6. Replies
    7
    Views
    930

    Check down by the lube tank for a single gauge on...

    Check down by the lube tank for a single gauge on the side of the panel nearest the lube tank. If there is one there, adjust it slightly to reduce the flow. Don’t go too low with it...
    If the above...
  7. Replies
    12
    Views
    884

    EBay item 392272132884 Turn the face flat with...

    EBay item 392272132884
    Turn the face flat with the hole and raised boss for the Renishaw probe and add the two 8mm set screws? At worst, I should imagine heating the front end to soften it.
    Is this...
  8. Replies
    12
    Views
    884

    Hi, Andrew. Brent here! How about getting a VDI...

    Hi, Andrew. Brent here!
    How about getting a VDI 40 blank from eBay and adding the Renishaw probe mount to it?
  9. Make sure you have air blowing out of the lens...

    Make sure you have air blowing out of the lens holes as there are shutters in there that open with about 30psi on the gauge. Normally, the LEDs would be green on power up with air present.
  10. Replies
    23
    Views
    1,457

    Download Solid Edge. Great little program with...

    Download Solid Edge. Great little program with nice features.
  11. Replies
    14
    Views
    1,473

    Belt noise?

    Belt noise?
  12. If you have access to the screws holding the...

    If you have access to the screws holding the unclamping cylinder down, undo the screws/nuts by about 1/4” and put a piece of aluminium in the gap between the piston and the drawbar (aim for a snug...
  13. I’ve fitted a few of these to Hurco 5 axis...

    I’ve fitted a few of these to Hurco 5 axis VMX30Ui machines. I’ve done two two-machine one robot cells and they work really well. Erowa robots are a really nice piece of equipment.
  14. How about a Hurco BX40? Dual column, linear...

    How about a Hurco BX40? Dual column, linear scales, 18k HSK63 Kessler spindle.
  15. Replies
    11
    Views
    1,149

    Excellent!!

    Excellent!!
  16. Replies
    11
    Views
    1,149

    If I remember correctly, the wiring was in this...

    If I remember correctly, the wiring was in this order in the plug to the monitor:
    Video
    0V
    15V
    0V
  17. Replies
    11
    Views
    1,149

    The output is just composite video (just like the...

    The output is just composite video (just like the signals that run in the yellow plug on older VCRs).
  18. Replies
    37
    Views
    1,815

    Ok. Thanks for that. I was just wondering.

    Ok. Thanks for that. I was just wondering.
  19. Replies
    37
    Views
    1,815

    What is the material?

    What is the material?
  20. You could use the tools but only in a manual...

    You could use the tools but only in a manual capacity. The flanges are way different and will jam up in an auto toolxhange.
  21. Hurco Hawk 2U CNC Mill - YouTube...

    Hurco Hawk 2U CNC Mill - YouTube
  22. It’s an Ultipath control. Hurco only did a few of...

    It’s an Ultipath control. Hurco only did a few of them and support is very limited. They were fitted to Hawk 2U machines.
  23. No worries, mate!

    No worries, mate!
  24. Hi, I’ve sent a reply on the other site..

    Hi, I’ve sent a reply on the other site..
  25. Replies
    12
    Views
    3,836

    Probably. Try the hard drive settings as I...

    Probably. Try the hard drive settings as I suggested on the other site and see what happens.
Results 1 to 25 of 397
Page 1 of 16 1 2 3 4