Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: markz528

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    15
    Views
    1,233

    Thanks! I meant IPM - IPS is a company I deal...

    Thanks! I meant IPM - IPS is a company I deal with........

    The machine is an Atrump bed mill with a Centroid control. My current coolant system is not very good. Bought the machine new around a...
  2. Replies
    15
    Views
    1,233

    Need advice on machining O-Ring groove

    I need to make a an o-ring groove that will capture the o-ring. In the past all the o-ring grooves I machined were for static pressure using the Parker guidelines and the o-rings move around in...
  3. Send me a PM..........

    Send me a PM..........
  4. As stated by others, for vfd installation the...

    As stated by others, for vfd installation the shield must be well bonded at both ends (drive and motor). The correct bushing for the cable should be used. The best VFD cable hands down that I know...
  5. Replies
    11
    Views
    828

    Industrial duty WEG motors are perfectly...

    Industrial duty WEG motors are perfectly acceptable. WEG has the best NEMA motor product manager hands down. But you want a Brazilian made motor not a Mexican made motor. Big difference.

    I have...
  6. Replies
    8
    Views
    767

    Can't comment on Vactra #1, but you can't get DTE...

    Can't comment on Vactra #1, but you can't get DTE Light in gallon containers anymore either. 5 gallon containers minimum.
  7. Replies
    4
    Views
    725

    Thank you very much!

    Thank you very much!
  8. Replies
    4
    Views
    725

    Sorry about the sideways picture, W10 really...

    Sorry about the sideways picture, W10 really screws me up. I can get it right on my W7 machine but not on my W10 laptop.
  9. Replies
    4
    Views
    725

    Why labeled 10K & Model A?

    My BIL recently acquired a 70's lathe from someone on this board. I'm confused by the nameplate. It says Model A. I thought a CL670Z was a 10K.

    I do have to admit that I don't know what a Model...
  10. Replies
    18
    Views
    2,036

    That was the 3 phase input. Below is the single...

    That was the 3 phase input. Below is the single phase input, and better yet the one on the bottom is 3 hp single or 3 phase input (that's the one I have on my lathe).

    AC Micro Drive: 240 VAC, 2hp...
  11. Replies
    18
    Views
    2,036

    I put a WEG CFW7 drive on my lathe (3hp) and its...

    I put a WEG CFW7 drive on my lathe (3hp) and its pretty decent. I would not hesitate to put one on a Bridgeport. You definitely want to run it in sensorless mode and use a braking resistor. This...
  12. Replies
    24
    Views
    1,385

    Very well said.........

    Very well said.........
  13. Replies
    8
    Views
    1,059

    I need one of those for my 16" Lost...

    I need one of those for my 16" Lost mine..........
  14. Replies
    22
    Views
    1,536

    Can it be polished to a high degree (not sure of...

    Can it be polished to a high degree (not sure of the proper terminology)? When I tried to polish the Delrin, I got it to shine but it was still a dullish black not like the results of the...
  15. Replies
    22
    Views
    1,536

    I found a picture of 2 that I made. Left one was...

    I found a picture of 2 that I made. Left one was a good one that I made and right is one already showing signs of cracking. The left one ultimately cracked also after a few months.

    257623
  16. Replies
    22
    Views
    1,536

    What material to make shifter handle?

    For my anal 65 Fury 2 door cop car restoration with a 3 on the tree standard, I can't buy a handle and need to make it. It needs to be shiney plastic.

    I made 3 of them (was practicing) out of...
  17. Replies
    29
    Views
    2,294

    Oops. looked at the door again. Not what I...

    Oops. looked at the door again. Not what I thought the first time. Looks more like a 13" now to me, but I don't know anything about the 11" models.
  18. Replies
    6
    Views
    742

    Did H4 get vaporized? Did you follow inside the...

    Did H4 get vaporized? Did you follow inside the panel to see if there was evidence of H4?

    As stated, you need a H4. I doubt someone custom wound the transformer. Is there a nameplate on the...
  19. Replies
    41
    Views
    3,014

    I don't think that is correct. I belive that is...

    I don't think that is correct. I belive that is a 3 phase panel. Check out this ebay ad for the same panel model number...........

    Square D QOC-30 QO Load Center Electrical Cabinet | eBay
  20. So whether a 50 or 60 hertz motor is more...

    So whether a 50 or 60 hertz motor is more efficient really depends on the design. For sake of discussion, we should assume that the motors will have the same efficiency.

    The generator running at...
  21. Replies
    29
    Views
    2,294

    So it looks like a 16 inch to me and it is old -...

    So it looks like a 16 inch to me and it is old - how old I don't know. Its not a 13 inch because of the door, but not sure what door the 14 1/2 lathes have so maybe it could be a 14 1/2. But it has...
  22. Replies
    2
    Views
    552

    I will take them. Will send a PM.

    I will take them. Will send a PM.
  23. Replies
    11
    Views
    1,214

    Its very happy in its new home. Thanks RT! ...

    Its very happy in its new home. Thanks RT!

    256900
  24. Replies
    35
    Views
    3,588

    Very sorry to hear. I almost dropped my 16 inch...

    Very sorry to hear. I almost dropped my 16 inch getting off the trailer - my wife is still rolling her eyes over that one. I dropped my Reid hydraulic surface grinder on its back getting it off the...
  25. I should clarify - the customer wants 32 RA for...

    I should clarify - the customer wants 32 RA for the shaft extension and all other purchased motors get the 32 RA. This particular motor design is not purchased very often and has a separate spec and...
Results 1 to 25 of 173
Page 1 of 7 1 2 3 4