Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: chad883

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    9
    Views
    403

    Probably a dumb question, but did those sub...

    Probably a dumb question, but did those sub programs actuallymake it to the machine? Could it have timed out before finishing?
  2. Replies
    6
    Views
    324

    I got the file downloaded. Looking at the...

    I got the file downloaded. Looking at the drawing, I need to get in from the tail stock end, loosen 10 bolts to pop the drive loose. Then get the motor to orient and get my drive lug set correcty....
  3. Replies
    6
    Views
    324

    P.M. sent with my email Thanks

    P.M. sent with my email

    Thanks
  4. Replies
    6
    Views
    324

    Mori SL25Y live tool drive

    I have a Mori SL 25Y, while drilling a cross hole with a live tool the coolant ran dry. This stopped the drill and alarmed the machine. I got everything reset and homed out. The problem is that the...
  5. Replies
    6
    Views
    515

    I have only ran these on a CNC. 1. Yes 4TPI...

    I have only ran these on a CNC.
    1. Yes 4TPI would be the correct pitch for a 4 start 16 TPI

    2. Not sure on this one.

    3.On CNC I ran one thread complete, then started again at different Z start...
  6. Replies
    12
    Views
    1,073

    I run a 4" face mill 8000 RPM in aluminum, I...

    I run a 4" face mill 8000 RPM in aluminum, I can't say that the TSC is hitting the inserts, but I can say that flood is not. The wind generated from the face mill makes an air curtain that prevents...
  7. Replies
    11
    Views
    1,025

    Did this machine have a bar feeder hooked up? If...

    Did this machine have a bar feeder hooked up? If so it may be seeing the bar feeder e-stop circuit and throwing other alarms from that.
  8. Replies
    0
    Views
    504

    Opinions on 1998 MC-V4020

    I am considering expanding my mill capacity with one of these. Please let me know the good, the bad, and the ugly. Also a ballpark value.

    Thanks
  9. Replies
    6
    Views
    677

    Probably the air line going into the tool eye...

    Probably the air line going into the tool eye that blows on the eye when you are touching off tools. Just a guess though.
  10. I usually sync them with 1 of the chuck open so...

    I usually sync them with 1 of the chuck open so they don't fight. May not be necessary.
  11. Only thing I can see, and I'm not sure it...

    Only thing I can see, and I'm not sure it matters, is the G50Z line. I use G50 W-[#102]. Just be careful that it is shifting the offset in the right direction.
  12. T0121.02G0G40(TRANSFER) M306(SUB CHUCK OPEN)...

    T0121.02G0G40(TRANSFER)
    M306(SUB CHUCK OPEN)
    G99G18
    G28U0.
    G0Z0.
    G0B-16.
    G97M3S50
    M358(AIR BLOW)
    M5
    M200
  13. Hi Mike. It is looking for one to be made and one...

    Hi Mike. It is looking for one to be made and one not. If I remember correctly you can use a wench, or any piece of steel to see if they are working. Mine have lights on the side of them for when...
  14. Replies
    8
    Views
    1,144

    Low hydraulic pressure might be a phase issue,...

    Low hydraulic pressure might be a phase issue, which could cause the e-stop. switch 2 legs and see if you get pressure
  15. Replies
    61
    Views
    2,452

    Glad I could help. The funny thing is the 100...

    Glad I could help. The funny thing is the 100 Integrex does not have this file. It doesn't seem like it does much, but I think it is more that it is looking for that sub program to run and not...
  16. Replies
    61
    Views
    2,452

    Yes I know it doesn't seem like it does any good,...

    Yes I know it doesn't seem like it does any good, but that is what fixed it. Had the same thing happening, it would change tools and seemed like it completed, but would just sit there.
  17. Replies
    61
    Views
    2,452

    You have to go into the windows side and get into...

    You have to go into the windows side and get into the c drive. You will find a bunch of folders, open up the T_PLC PROGRAM folder. There should be a G code program 9000

    G91G01Y-0.01
    G01Y0.0101...
  18. Replies
    61
    Views
    2,452

    Be very careful here. Parameters from a like...

    Be very careful here. Parameters from a like machine are a good start, but the ladder can be very different with options that you do or don't have. Also there are different versions of the ladder for...
  19. The only other thing I can think of is if you are...

    The only other thing I can think of is if you are still on the sub side (M300), if so try M302 before moving sub and part catcher
  20. I don't think so, the book for that machine lists...

    I don't think so, the book for that machine lists bit 5 for S, MS Parts catcher - B axis home interlock.

    This manual does give bits 1-4 as turret rotation interlock home, 1=X axis auto, 2=X axis...
  21. I just checked on our 1995 SQT 15 MSY. R70 all...

    I just checked on our 1995 SQT 15 MSY. R70 all 0, part catcher will not work with B axis off home. R70 0010000 part catcher will extend with B not home, can not move B with parts catcher out. All...
  22. Complete shot in the dark, but have you tried...

    Complete shot in the dark, but have you tried barrier cancel?
  23. Also my R70 00100010 book says 0 1 2 3 4...

    Also my R70 00100010

    book says
    0
    1
    2
    3
    4
    5 S, MS PARTS CATCHER B AXIS HOME INTERLOCK 0 USE 1 NOT USE
    6 CARRIGE JOINT TYPE 0 1 VALID
  24. This came out of my machine after job was done. ...

    This came out of my machine after job was done.

    T0909G0G40
    G0X6.0Z5.5
    M302
    G0B-1.0
    M48
    M306
    M358
    M49
  25. I have extended parts catcher moved sub into...

    I have extended parts catcher moved sub into position (away from home), open chuck, home sub, retract parts catcher. Not the best, but it gets the part into the catcher.
Results 1 to 25 of 144
Page 1 of 6 1 2 3 4