Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: BuffDan

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. I could sure use that microscope light!! PM...

    I could sure use that microscope light!!
    PM incoming.
    Thank you!!
    Dan
  2. 291362I use a plastic hood that Grizzly sells.....

    291362I use a plastic hood that Grizzly sells.. $10.. I''m not in a production mode, so will last for me
  3. hood, chute, scoop....

    hood, chute, scoop....
  4. Replies
    25
    Views
    2,264

    Sent pm, but couldnt add image for some...

    Sent pm, but couldnt add image for some reason290219
  5. Replies
    25
    Views
    2,264

    I'd be interested in wheel arbors such as290196

    I'd be interested in wheel arbors such as290196
  6. Replies
    11
    Views
    1,021

    icarbide was making them, but I dont see them...

    icarbide was making them, but I dont see them anymore
  7. how much ?

    how much ?
  8. looks like Rockwell 11 YouTube...

    looks like Rockwell 11
    YouTube
  9. 288692 The magnets popped right out, they were a...

    288692
    The magnets popped right out, they were a press fit.
    They sure are weak..
    I ordered some neodymium 1/2x1/8 magnets.. They will fit inside the inner brass shields. I will probably have to...
  10. I haven't used it because the magnets don''t...

    I haven't used it because the magnets don''t hold it in place very well.. I have cleaned it and painted since the attached photo.. I view this as a project, learning, etc. I believe it can be a...
  11. Replies
    6
    Views
    729

    Sent me scam PM also

    Sent me scam PM also
  12. Thanks for the input... The magnets have 2 brass...

    Thanks for the input... The magnets have 2 brass shells and 2 steel for the magnet.. I'll have to get one out, hopefully intact..
    Not sure if I need to replace with magnet that has outer brass...
  13. Thanks for your reply Richard... They make...

    Thanks for your reply Richard... They make fantastic products.. But I cant justify their cost for this piece.
  14. Weak magnets in cylindrical square- Re-energize, or replace?

    This cylindrical square has weak magnets, barely enough to hold it in place.
    Can I re-charge them, or replace them?

    Thanks.
  15. Replies
    4
    Views
    812

    Leblond says: f you cannot find the desired...

    Leblond says: f you cannot find the desired information, please complete the Contact Form and your request will be answered promptly. (NOTE: Serial Numbers can be found on the upper back corner of...
  16. Replies
    4
    Views
    493

    I may have a source.. But plan B is to make...

    I may have a source..
    But plan B is to make them. I have a rotary balancing stand for grinding wheels which I will use. I realize dynamic balancing would be better, but i dont have that capability....
  17. Replies
    4
    Views
    493

    WTB Ko Lee cutter grinder pulleys

    I need pulleys for my KO Lee cutter grinder. (b6060)
    It uses the 5M series 3/16 belts.

    The spindle pulleys are 5/8 ID , and the motor pulleys are 3" TPF using 5M series 3/16 belts.
    .
    I...
  18. Thanks Larry, makes sense. Dan

    Thanks Larry, makes sense.
    Dan
  19. When would you use a 90 degree center?

    I acquired this a while back, and have been searching for 90 degree dead centers, but cant determine when you would use 90 instead of 60 degree.

    Or is this a "blank waiting to be properly ground?...
  20. Replies
    42
    Views
    5,869

    I hope its more accurate than their labeling:...

    I hope its more accurate than their labeling:
    285129
  21. Replies
    3
    Views
    447

    vintage machinery.org has it.. they have a lot...

    vintage machinery.org has it.. they have a lot of manuals.. free download, but they take donations
  22. Replies
    11
    Views
    1,272

    approximately

    approximately
  23. Replies
    6
    Views
    757

    Thanks for your reply. I think because the key is...

    Thanks for your reply. I think because the key is so small I need to make it from one piece. The key is .062 x .125..

    Dan
  24. Replies
    6
    Views
    757

    Where can I buy a peg feather key??

    Any ideas on who might sell peg feather keys, such as in the pictures
    I have tried the usual, McMaster, grainger, fastenal...

    I need just one.. I will probably end up making one, but thought I'd...
  25. Replies
    459
    Views
    22,591

    I spray all items incoming to the house with...

    I spray all items incoming to the house with straight isopropyl. Mail, deliveries, packages/items from grocery delivery, etc
Results 1 to 25 of 130
Page 1 of 6 1 2 3 4