Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: kustomizer

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    62
    Views
    9,245

    When I was a little guy my grandpa gave me a...

    When I was a little guy my grandpa gave me a fisher price tool bench, the one with round, square and hex pegs, matching holes, a plastic hammer, pliers and screwdriver for my birthday. I have always...
  2. Replies
    11
    Views
    560

    I had that problem too, I ended up drilling and...

    I had that problem too, I ended up drilling and tapping 5/8 -11 holes every 8 inches on a 45 degree angle all over the 2' x 12' bench, after I had a few in I has able to hold the drill press in place...
  3. I have some deburring stations mounted to a 10'...

    I have some deburring stations mounted to a 10' dualdraw downdraft table that works great, sometimes I have a need to use a 6x72 horizontal belt grinder graining some aluminum parts. I found after...
  4. Replies
    11
    Views
    560

    I used a benchtop drill press clamped to the...

    I used a benchtop drill press clamped to the table with c-clamps and a long drill
  5. there could be some truth in this 323105

    there could be some truth in this
    323105
  6. I see a massage gal and then a Chiropractor in...

    I see a massage gal and then a Chiropractor in the same office every month and have not had back trouble other than sore muscles in years which is saying a lot given my size, when you get to be 6'8...
  7. Replies
    20
    Views
    950

    Nicely done, keep us in the loop as you progress.

    Nicely done, keep us in the loop as you progress.
  8. Replies
    20
    Views
    950

    My fear in making them is that the part at risk...

    My fear in making them is that the part at risk is the spindle, sometimes the tool holders stick pretty hard in the spindle putting a lot of stress on that little part, the ones you have sell for...
  9. Replies
    20
    Views
    950

    They still list them and the BT40, for the price...

    They still list them and the BT40, for the price I would buy the ct's and sell your bt's to get a few bucks back
    EXTRACTOR, CT40 UMBRELLA T/C FINGER PRE S/N 6701 | Carousel Plate Components |...
  10. For pre anodize we deburr in ceramic triangles...

    For pre anodize we deburr in ceramic triangles too worn for steel then into a second tumbler with 3mm ceramic balls, they come out bright and shiny, almost polished. the waste water from each machine...
  11. Replies
    195
    Views
    11,408

    I got word my magneto is on its way home and got...

    I got word my magneto is on its way home and got a test video to go with it, kinda cool the test machine, I will try to post it.
    Nope, cant do it, sure seems this stuff could be easier to load on...
  12. 90% of our problems went away when we switched to...

    90% of our problems went away when we switched to ceramic media and threw out the plastic, we found it by accident when I bought a used tumbler with very worn ceramic triangles and put a few parts in...
  13. Replies
    114
    Views
    26,945

    I have warer tights to use warer from our...

    I have warer tights to use warer from our irrigation ditch as well as pump direct from the river as I do to irrigate our pastures, it could go through the shop in its way to the sprinlkers at about...
  14. Replies
    114
    Views
    26,945

    Well, I think the jury is in, we have been in the...

    Well, I think the jury is in, we have been in the mid 90's most of the week, it cools off to the mid 50's at night which is typical here.
    I put in a 14" version of one of these fans in the ceiling...
  15. Replies
    73
    Views
    4,324

    I have often wondered why we can't throw all the...

    I have often wondered why we can't throw all the tax laws out and simply use "sales tax", the more you buy the more tax you pay. It seems to be the only "fair tax", but there must be a reason besides...
  16. I wonder if an air solenoid could make that kind...

    I wonder if an air solenoid could make that kind of noise? I would call the factory, they are very helpfull troubleshooting and are free.
    they will want the serial number.
  17. Something I learned years back is the relays work...

    Something I learned years back is the relays work better longer if you open them up and file the peaks off them with fine sandpaper, once this is done they seem to last forever, if you replace them...
  18. Replies
    195
    Views
    11,408

    Around these parts are these types, they have no...

    Around these parts are these types, they have no respect for the folks using the roads making good brakes a must.

    322042
    322043
  19. Replies
    195
    Views
    11,408

    My " Made in Australia" dual leading edge brake...

    My " Made in Australia" dual leading edge brake system showed up and the quality of machining rivals any I have ever seen ( very nicely done ). It is an adaptation of 68-70 Triumph front brake (...
  20. Replies
    21
    Views
    1,272

    Ma gave us gourds, she had pops file and sand the...

    Ma gave us gourds, she had pops file and sand the stem smooth, big enough to slobber on but not small enough to fit in the mouth and she grew them herself

    Later we had blocks made from twp 1/2...
  21. Stressproof welds fine and turns better than 1018

    Stressproof welds fine and turns better than 1018
  22. I think I would start with 12;14, we used to make...

    I think I would start with 12;14, we used to make shift levers from 5/8 dom tube with a .188 hole from 5/8 to 3/8 od from 6" to 30" in length, kind of like this video, the dom tube was gummy, 12l14...
  23. Replies
    7
    Views
    669

    Brass or copper base rather than steel?

    Brass or copper base rather than steel?
  24. I started making "job boxes" about 25 or more...

    I started making "job boxes" about 25 or more years ago, I started with rubbermaid boxes and graduated to ammo cans, 50 cal for big jobe and 30 cal for smaller jobs. Each box has sample parts, mating...
  25. Replies
    577
    Views
    106,488

    To keep it vertical, without it the table would...

    To keep it vertical, without it the table would rock around with the load upon it.
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4