Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: M. Moore

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    2
    Views
    293

    I might have something, I will have to remember...

    I might have something, I will have to remember to have a look.
  2. Eagle, I forgot to include that I have the...

    Eagle,
    I forgot to include that I have the Anilam 3000M, 3 axis control.
    Interesting to know that you used Gcode and converted directly on the machine.
    I read that it can do that but have not...
  3. Update, Eventually I figured it out. Set up a...

    Update,
    Eventually I figured it out.
    Set up a master loop to include the RMS and its sub #1 and set the master loop with z increment.
    Almost sounds like I know what I'm talking about.
    With a...
  4. Replies
    26
    Views
    1,190

    Good work in getting it back running. Also thanks...

    Good work in getting it back running. Also thanks for posting clearly what you had to do to resurrect the machine.

    Also thanks to those posting suggestions for what might work as a retrofit...
  5. Replies
    66
    Views
    3,089

    Wow, You guys have been busy typing. I see...

    Wow,
    You guys have been busy typing.
    I see only one or two honest answers in the bunch, and a lot of crap.

    Personally I surmised that the lack of tides would have some impact on the life forms...
  6. Replies
    66
    Views
    3,089

    Earth with no Moon?

    Kind of a technical question....
    Hope this doesn't get locked as I am interested in the answer.

    What would the Earth be like without a moon?

    I am only interested in plausible scenarios...
  7. Anilam programming for beginner...repeat/loop/sub?

    Just learning and sometimes it is hard.
    Mostly I bang my head against the wall because if the Z axis. I find that one to be the hardest to get used to, x and y are almost invisible now.

    So, I...
  8. Replies
    21
    Views
    8,315

    My experience with foaming was too high of a...

    My experience with foaming was too high of a concentration from older coolant having evaporated and I tried adding a slightly richer mix. The richer mix quickly caused the foaming issue.
    The...
  9. Replies
    26
    Views
    1,190

    I am watching this with interest as I have an...

    I am watching this with interest as I have an Anilam 3000 control and hopefully it will last 20 years or so....

    Have you tried the Anilam parts suppliers that are easily found with a quick search?...
  10. Replies
    9
    Views
    1,046

    That machine looks pretty good for its age....

    That machine looks pretty good for its age.
    Sorry, not a potential buyer but I was just curious what material is used for the door glass?
    Those are the cleanest doors I have seen on a VMC.
    I...
  11. Robf, Want to post a link? I did a quick search...

    Robf,
    Want to post a link? I did a quick search and came up empty on pricing.
  12. I am interested but it is missing 8 of the...

    I am interested but it is missing 8 of the standard quick change holders that should be in the set.
    Buying those separately may break the bank unless you have them and didn’t take any photos? ...
  13. Replies
    5
    Views
    835

    There is a two for one deal on exactly what you...

    There is a two for one deal on exactly what you are looking for but it is on the west coast.

    Check out the for sale posts by pm member Collector.
  14. Not sure if this helps but I have a complete 1100...

    Not sure if this helps but I have a complete 1100 control with documentation.
    I think the discs are there as well.
    My new to me mill had been upgraded to the 3000M control and the previous owner...
  15. I will check but most are not marked as per...

    I will check but most are not marked as per Johnoders comments.
    Which I am guessing means that unmarked cutters are usually 14.5°.
  16. Replies
    9
    Views
    484

    Gear cutters for sale 14.5 PA, Sprocket and Bevel...

    Gear cutters for sale 14.5 PA, Sprocket and Bevel cutters

    Should be here if the link works.....
  17. Replies
    9
    Views
    484

    I've got a 9 #5 listed here on the PM for...

    I've got a 9 #5 listed here on the PM for sale.....
  18. Replies
    4
    Views
    414

    Hardplates, Nothing is obvious to me at this...

    Hardplates,
    Nothing is obvious to me at this stage......
    This control is not a G-code system.

    Another mystery is that when running a named program canned cycle the code is displayed on the...
  19. Replies
    4
    Views
    414

    Dan, thanks for the reply. All is well after a...

    Dan,
    thanks for the reply.
    All is well after a reboot this morning.
    Ran the same MDI program and it was all normal. Not sure what happened.
    It is all new to me so it was probably something I...
  20. Replies
    4
    Views
    414

    MDI runs in rapid? (Anilam 3000)

    I am just learning my how to program the CNC on my Anilam 3000 control.
    I think it is going well with a few hiccups.
    I recently did a short program with MDI and cut a simple pocket, it was pretty...
  21. Replies
    3
    Views
    529

    Email coming regarding the CAT40 list. Thanks...

    Email coming regarding the CAT40 list.

    Thanks
    Michael
  22. If you get a laser isn't it likely that you will...

    If you get a laser isn't it likely that you will have the same problem as the originals?

    You mentioned the type of laser you want to buy, is it significantly better than the laser that was used...
  23. Replies
    35
    Views
    2,512

    Goldsmith, Those do look good! Your 5’er just...

    Goldsmith,
    Those do look good! Your 5’er just has the one main cylinder and two guide columns?
    How much?
    Here is a link to the Kaasto info page, HPA-P | Hydraulic Workshop Press Brake | KAAST
  24. With such tolerances if you happen to have a...

    With such tolerances if you happen to have a 2.25" annular cutter then just clamp a scrap piece of 1x3 to the edge and drill through on the correct centre point. Very fast and easy.


    (Gustafson...
  25. Replies
    12
    Views
    871

    John, That is a usage that I did not consider...

    John,
    That is a usage that I did not consider but of course would work very well. Unobstructed access to all four edges definitely speeds things.
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4