Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: boosted

Page 1 of 15 1 2 3 4

Search: Search took 0.01 seconds.

  1. Mazak definitely won't be out of the budget. ...

    Mazak definitely won't be out of the budget. Hermle would probably be the biggest stretch, but you might be surprised at the affordability of their smaller machines. All of the big builders make...
  2. Almost everybody makes a 5 axis machine with a...

    Almost everybody makes a 5 axis machine with a stand alone pallet pool, and for 500k you should have a ton of options. Personally (and this is subjective) I wouldn't consider either of those...
  3. Replies
    304
    Views
    16,616

    Scott I never said anything regarding infection...

    Scott I never said anything regarding infection rates, etc... I absolutely believe that the media is fear mongering, and it is totally possible that this is blown out of proportion.

    It also...
  4. Replies
    304
    Views
    16,616

    Are you fucking kidding me? So damn sick of...

    Are you fucking kidding me? So damn sick of everything being charged with identity politics. When is it a confirmed fact? When your cousin's brother-in-law's doctor says so? Once they declare it...
  5. Replies
    304
    Views
    16,616

    Bob, either you are being combative or shamefully...

    Bob, either you are being combative or shamefully ignorant.

    It is common knowledge at this point that unlike the flu, an alarming percentage of patients who recover from this virus require...
  6. Replies
    304
    Views
    16,616

    For Pete's sake, have you seen how overwhelmed...

    For Pete's sake, have you seen how overwhelmed the medical infrastructure is right now!? You are absolutely being flippant.

    Mortality rates will go up significantly if we run out of medical...
  7. Replies
    4
    Views
    581

    Assuming that it is still the same basic casting,...

    Assuming that it is still the same basic casting, rails, etc... as the 460/560, I think you'll be way happier with the 40 taper. While they are quite robust, it's not the type of machine where I'd...
  8. And contrary to popular belief; I'm pretty sure...

    And contrary to popular belief; I'm pretty sure that long reach Haimer ER-16 costs less than the Accupro CAT40+ it is sitting next to.
  9. So nobody chiming in has actually answered the...

    So nobody chiming in has actually answered the question?

    As for the "why?" -that's a dumb question. Even if there was no performance advantage, there are plenty of reasons for some folks to...
  10. Seriously, fuck right off with this. Now's...

    Seriously, fuck right off with this.

    Now's not the time. We're all in this together.
  11. Replies
    304
    Views
    16,616

    I guess it depends when everybody else stops...

    I guess it depends when everybody else stops paying. If cash quit coming in tomorrow; 60 days would wipe out all of our business savings. We could maybe make it 90 days if I dug into the personal...
  12. Replies
    20
    Views
    1,138

    Okay, so here's my update after a couple weeks. ...

    Okay, so here's my update after a couple weeks.

    - Pumped the original charge of 630XT out of the machine, and hit it with a fresh batch. Went ahead and changed one of the other machines over at...
  13. Replies
    20
    Views
    1,138

    I did clean out the machine with Whamex prior to...

    I did clean out the machine with Whamex prior to filling. However, we just drained the sump and then recharged. It could be reacting to the old coolant that was still in the lines, etc.

    Just for...
  14. Replies
    20
    Views
    1,138

    Trim 690XT Smell

    Hey guys just reporting my experience. I finally gave up on Blaser Synergy 735 due to staining, rusting, and poor performance (especially with form taps).

    After extensive research online, and...
  15. Replies
    113
    Views
    10,055

    Not much really. But if I don't keep up with...

    Not much really. But if I don't keep up with their 5 service packs a year I can't open native solidworks parts sent to me by about 25% of my customers. It's absolutely a scam, but I also don't want...
  16. If you refuse to believe statistics which are...

    If you refuse to believe statistics which are widely recorded from multiple sources, then there is no hope. Large studies of both reported and non reported crime mimic that data. Kinda shameful...
  17. Replies
    10
    Views
    1,066

    Even just a halfway decent cobalt jobber drill...

    Even just a halfway decent cobalt jobber drill will make short work of your feature. If you want to get fancy the aluminum-specific ones are nice.
  18. Replies
    2
    Views
    297

    Yep, same. Turned out one of the machines did...

    Yep, same. Turned out one of the machines did not have the macro option.
  19. Replies
    33
    Views
    3,089

    I typically leave about .0005in of clearance all...

    I typically leave about .0005in of clearance all around. The sides trap the part and keep it from rocking/twisting. At least in my experience it seems much more secure that way.

    If you've never...
  20. Look guys, obviously violent encounters happen. ...

    Look guys, obviously violent encounters happen. However, I think we need to recognize that (at lease here in the US) violent crimes as a whole have been sharply declining over the last 30 years. ...
  21. Replies
    113
    Views
    10,055

    Probably OnShape?

    Probably OnShape?
  22. Replies
    113
    Views
    10,055

    Wait, you actually own SolidWorks? Cus I just...

    Wait, you actually own SolidWorks? Cus I just got hit with a ~$1500 invoice for next year's maintanance on my ~$3000 license. Sure feels like a subscription to me.
  23. Replies
    33
    Views
    3,089

    Because I'm in a hurry to remove material dammit!...

    Because I'm in a hurry to remove material dammit! If the part's not trapped on all sides there is a way higher likelihood it's getting sucked out during OP2.

    Another big fan of mickey mouse...
  24. That wasn't my point. I'm a huge fan of personal...

    That wasn't my point. I'm a huge fan of personal freedoms. If you want to deal with weirdos by brandishing a firearm, then by all means do it.

    I just don't appreciate oversimplifications such as...
  25. Years of watching John Wayne and Clint Eastwood...

    Years of watching John Wayne and Clint Eastwood lead me to believe otherwise! :skep::skep::D

    Seriously though you ever been to Japan? That's sorta the epitome of polite society, and yet narry a...
Results 1 to 25 of 371
Page 1 of 15 1 2 3 4