Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: pcasanova

Page 1 of 19 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    395

    had an issue similar to your turned out to be the...

    had an issue similar to your turned out to be the acrylic chips got packed in behind the master collet and wouldnt let the sleeve come forward far enough. It was packed in so much I thought it was...
  2. Replies
    7
    Views
    522

    markp just had to do what you did. you can...

    markp just had to do what you did. you can search the threads to look him up, I don't think it was longer then 6mo ago. worst case if you cant find someone to copy the hd, get the other guys...
  3. try moving g0 g53 d0 z2=28 then start your...

    try moving
    g0 g53 d0 z2=28

    then start your code and see if it still alarms
  4. is there any d numbers set? and are you bringing...

    is there any d numbers set? and are you bringing rhe z2 into a position before you start?
  5. I'm thinking thats not all the code, are you...

    I'm thinking thats not all the code, are you setting a g94? and if there's a g1 and no f set it will look at the last f that was set. I don't think it will go program to program but if you had a...
  6. not sure if this will work but try spos[1]=0...

    not sure if this will work but try

    spos[1]=0
    g91
    g1 c1 360 f.2 z2=-.5

    and see if the z2 interpolates with the c movement

    if for some reason the control doesn't like the 360
    just break it...
  7. spos[1]=0 g91 g1 c360 f.2 g1 c360 f.2 g1 c360...

    spos[1]=0
    g91
    g1 c360 f.2
    g1 c360 f.2
    g1 c360 f.2
    g1 c360 f.2
    g1 c360 f.2

    something like this
  8. even shitty inserts should have done better then...

    even shitty inserts should have done better then that, are you running the spindle backwards?
  9. All the siemens I've dealt with were 400v. I...

    All the siemens I've dealt with were 400v. I would look for a separate transformer and check it at cold start
    to see if it's putting out the voltage, pretty sure it's going to be a 230/115 that's...
  10. Replies
    96
    Views
    6,900

    or the turret rebuild I should be doing 282185...

    or the turret rebuild I should be doing

    282185

    but in my defense the parts are supposedly 10 days out. But they are coming from Italy, so I'm not gonna hold my breath
    on that one.....
  11. do you have the wiring diagram? also wondering...

    do you have the wiring diagram? also wondering if something in the drawbar is hung up not hitting a prox.
    I've also had prox light up but not giving the signal (rare but i've had it happen). but...
  12. with the umbrella back does the prox that sees...

    with the umbrella back does the prox that sees position light up?
  13. can you power the machine down and pull the...

    can you power the machine down and pull the umbrella out to a change position or if you can see the prox put a screw driver to trick it?
  14. your dealing with builder code. sounds like...

    your dealing with builder code. sounds like something a out of order, prox sensor not being seen.
    I don't think a plc reset will do you good. I'm sure there's a recovery procedure, but from your ...
  15. Replies
    60
    Views
    5,364

    there's always 2 sides. We had an employee call...

    there's always 2 sides. We had an employee call in sick, like no problem get better. a week dragged into 2, then 3 and we're like WTF. Then come to find out he had a new job but kept us in the...
  16. Replies
    1
    Views
    275

    asking which way to go or do you need code...

    asking which way to go or do you need code samples? you could do either method you described, Ive done both. I've never worked with the FMB so I don't know if it's servo loader like the LNS or just...
  17. If the 465 has a 840c and 611a drives control...

    If the 465 has a 840c and 611a drives control walk away. We just sent a 465 to scrap, the turrets needed to be rebuilt but siemens no longer supports the 840c and we weren't going to sink all the...
  18. don't drill into the next part. If the drill...

    don't drill into the next part. If the drill point is visible in your next part and it walks just a bit, your drill is going to get pulled and not drill straight. then your tap doesn't have a chance.
  19. Replies
    3
    Views
    949

    thanks for the quotes. job has been awarded.

    thanks for the quotes. job has been awarded.
  20. Replies
    19
    Views
    1,835

    most definite. having parts drop complete, no...

    most definite. having parts drop complete, no second handling gonna pay for itself pretty quick.
    then when a new part comes up your going to go think thank god we did that. also consider y axis....
  21. Replies
    3
    Views
    949

    simple swiss job - dowel pin

    Need a quote on - .127-.128dia x 1.00 pin .015chamfer each side, 303 or 304 stainless will need certs.
    1200 qty and 1500qty
  22. Replies
    28
    Views
    5,196

    yea I did the pp route with the 10hp box about...

    yea I did the pp route with the 10hp box about $3300. works like a champ.
  23. Takeover when the sub come in and clamps the...

    Takeover when the sub come in and clamps the part. Try your turret cycle program you wrote and add chuck open and close for both main and sub. Try that and see where your main hyd pressure goes.
  24. does it happen after the takeover? if so check...

    does it happen after the takeover? if so check your hydraulic pressure when the turret indexes and chucks cycle. maybe a weak pump or blowby on a clamping cylinder or combo of both
  25. I would contact QPM. I remember something in...

    I would contact QPM. I remember something in their catalog that said if you have an idea let us know. So they may be able to make something for you.
Results 1 to 25 of 464
Page 1 of 19 1 2 3 4