Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: GENERALDISARRAY

Page 1 of 15 1 2 3 4

Search: Search took 0.01 seconds; generated 17 minute(s) ago.

  1. Replies
    4
    Views
    437

    If you have an optical probe, and go put it in a...

    If you have an optical probe, and go put it in a shoebox. But still get false triggers. Something is up with your wiring, receiver, interface box (if equipped) or something else on the machine.
  2. Replies
    5
    Views
    240

    01-855-dmg-mori / 01-855-364-6674

    01-855-dmg-mori / 01-855-364-6674
  3. I have a mv40, no belts though. This drive was...

    I have a mv40, no belts though. This drive was used for a long time by many builders.

    I would have a look at the belts. Think Horse not Zebra.

    Rigid tap was still a twinkle in an engineers eye...
  4. The torque limiting command on the 6044 drive is...

    The torque limiting command on the 6044 drive is on one of the inputs to the drive.
    One for low speed and one for high speed. TLML is pin 5 and TLMH is on pin 21 of connector CN1 the common for...
  5. Replies
    5
    Views
    596

    mori seiki MS850G

    New to me lathe. I dont think it is oiling enough. There is a tag on the apron that says the flowrate can be adjusted via screws. Any idea where these screws are?
    Is there any maintenance to be...
  6. Looks like someone ran a boring bar in there. I...

    Looks like someone ran a boring bar in there. I would never put a less than perfect adapter bore on a grinder. You'll jack up the arbor.
    They are only $64 new from mcmaster of all places.

    I think...
  7. Replies
    50
    Views
    3,270

    I would consider it bad, but I know zero about...

    I would consider it bad, but I know zero about Haas?
  8. Replies
    50
    Views
    3,270

    Is that coolant inside your turret? (pic 2, tool...

    Is that coolant inside your turret? (pic 2, tool station at 6:00)
  9. Excessed then gutted by my friendly neighborhood...

    Excessed then gutted by my friendly neighborhood nu-clear bomb factory.My friend has had the scrap contract there, on and off for some time.

    Your tax dollars at work.
  10. I know where there is a T51 sitting, with weeds...

    I know where there is a T51 sitting, with weeds growing up through it. Send him my way.
  11. Replies
    8
    Views
    333

    I was looking for the tree and missed the forest....

    I was looking for the tree and missed the forest. Hunting For the softkey labeled check.

    program softkey was it.
  12. algo se está moviendo, pieza, herramienta,...

    algo se está moviendo, pieza, herramienta, codificador de husillo
  13. Replies
    8
    Views
    333

    Fanuc 0iMD program check screen

    "new" machine
    Does anyone know how to enable the program check screen? I searched through the parameter manual, and saw the screen referenced several times, but nothing on how to get it to show up...
  14. makes sense. little wires to disconnect, big...

    makes sense. little wires to disconnect, big honkers going to the lugs on the side.
  15. so not all the power goes through the main...

    so not all the power goes through the main breaker? the lower right corner of the picture confuses me.

    Enhance . .
  16. https://youtu.be/AfVE8pDGOd4 this shop is...

    https://youtu.be/AfVE8pDGOd4

    this shop is still running a 3 and 4 axis machine. The 3 had its axis drives retrofitted to ac brushless about 8 years ago.
  17. They did it for . . reasons on the "SB"...

    They did it for . . reasons
    on the "SB" machines

    1 the TT control did not yet exist when that machine was designed.Thats why the twin 6 control setup

    2 they sold the machine with a choice of...
  18. a Superslant is different from a Conquest. I...

    a Superslant is different from a Conquest. I didnt read the linked post, so I dont know anything about it.

    Conquest is all Fanuc electronics.

    I really like mine.

    The turret index gearbox and...
  19. Easy make you new single axis beta drive the...

    Easy
    make you new single axis beta drive the first drive. Then send the fiber on to the big beta drive.

    Hard
    ladder changes to support the rotary
    parameters for the rotary
    drive number changes...
  20. This all sounds like justification to use with...

    This all sounds like justification to use with the brass to trade up. Reduced setup time = lower cost. increased part quality.
  21. I can give you some theories on why they dont...

    I can give you some theories on why they dont want you to do half indexes on it without more hardware.

    The indexer machines rely on the curvic to provide accurate positioning. The servo motor is...
  22. Replies
    13
    Views
    578

    6047 series drives on that? What does the...

    6047 series drives on that?
    What does the voltage measure at the input of the drive?
    I would look at what is said in the posts above, but also look for a backup drive on ebay. They are too cheap...
  23. I would look through the paper ladder, in the...

    I would look through the paper ladder, in the keep relay section. I have looked through mine (nh5000) and dont recall seeing anything about 1/2 degree.

    But i was not looking for that, so.
  24. Replies
    41
    Views
    3,034

    COMPACTline with Mitsubishi...

    COMPACTline with Mitsubishi

    If the same people whom wrote the text on this page, built the machine. I would look elsewhere.
  25. Like Hardplates said,Can you punch it out? I once...

    Like Hardplates said,Can you punch it out? I once had a 15MB that had a bad spot in memory. It was somewhere around the half capacity point. If you tried to use that much memory it would give a...
Results 1 to 25 of 356
Page 1 of 15 1 2 3 4