Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: 220swift

Page 1 of 51 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    9
    Views
    562

    Check and see if your lead screw and feed rod are...

    Check and see if your lead screw and feed rod are parallel with the ways.
    That should tell if the gear box needs to go up or down.

    Hal
  2. Replies
    5
    Views
    909

    You might send Tony some good pictures for his...

    You might send Tony some good pictures for his web site.

    Hal
  3. Replies
    38
    Views
    3,660

    Ash I just emptied my pm box. Hal

    Ash
    I just emptied my pm box.

    Hal
  4. Replies
    22
    Views
    1,593

    Scott A very Nice retirement present x 2. You...

    Scott
    A very Nice retirement present x 2.
    You are one of the few if not the only one, in the world, to own two 30" I/M 10EE's.

    Did you get a wiring diagram from Monarch ?

    Hal
  5. Replies
    162
    Views
    6,778

    Looks just what you need. Hal

    Looks just what you need.

    Hal
  6. Replies
    9
    Views
    1,159

    I would look at fixing the oil leak. Hal

    I would look at fixing the oil leak.

    Hal
  7. Replies
    36
    Views
    2,694

    Your hand wheel is nice and your cleaning job...

    Your hand wheel is nice and your cleaning job turned out great.

    Hal
  8. Replies
    15
    Views
    834

    Steve I'm glad I could help and am looking...

    Steve I'm glad I could help and am looking forward watching your progress.
    I should have taken more pictures and better notes. When I worked on my EE, I had a flip phone. I had to borrow my...
  9. Replies
    15
    Views
    834

    I was just talking about about the gear box, not...

    I was just talking about about the gear box, not the headstock.

    Hal
  10. Replies
    15
    Views
    834

    Steve it's been over six years ago. I might...

    Steve it's been over six years ago. I might forget something but I'll try to help you. I don't know the correct names of everything.

    Remove the Left/Right tombstone shaped selector box above gear...
  11. Replies
    15
    Views
    834

    Steve I only swapped the gear boxes. Everything...

    Steve I only swapped the gear boxes. Everything else was left in place.

    Hal
  12. Replies
    15
    Views
    834

    Steve I'm looking forward to following you...

    Steve I'm looking forward to following you progress.
    The inch gear box is about 160 lbs and the I/M gear box about 175 lbs.

    If you use a grinder to cut the clearance cuts. Do it out side, it's a...
  13. This would make a good sticky. Hal

    This would make a good sticky.

    Hal
  14. Replies
    305
    Views
    14,648

    Grant it sounds like I should add Hardware Sales...

    Grant it sounds like I should add Hardware Sales to my bucket list. :)
    I'm not sure if it would be good or bad to have a nice store like that close by. I would go to buy something and end up...
  15. Replies
    305
    Views
    14,648

    Grant Great job. Where do you get marine grade...

    Grant
    Great job. Where do you get marine grade crimps ?

    Hal
  16. Replies
    2
    Views
    7,255

    I have always like this picture. What a great...

    I have always like this picture. What a great shot of a grand saw.
    The old man makes the picture.

    Hal
  17. Replies
    23
    Views
    2,171

    Dan What a deal on your lathe. You might...

    Dan

    What a deal on your lathe.
    You might give Monarch a call and talk to Scott. Ask him if the have any used elsr rods for sale.

    Hal
  18. Replies
    38
    Views
    3,660

    On one lathe there were Z oil ways on both the...

    On one lathe there were Z oil ways on both the stationary saddle ways of the cross slide and the sliding part of the cross slide.

    Hal
  19. Replies
    21
    Views
    6,630

    Very nice looking paint job. Hal

    Very nice looking paint job.

    Hal
  20. Replies
    38
    Views
    3,660

    Ee parts

    Adm. I sent you a pm on the cross feed dial.

    Hal
  21. Replies
    4
    Views
    643

    Branden Thanks for the reply. Do you know what...

    Branden

    Thanks for the reply. Do you know what they are called and who made them?

    Hal
  22. Replies
    4
    Views
    643

    10EE tailstock oil cap

    What do you call the little unit that sits on top of the 10EE tailstock.
    You add oil and it has a little screw on cap with a keeper chain.
    I thought they were made by Gits. But all I could find...
  23. Replies
    268
    Views
    39,089

    Bob from Canada was looking for a top end cover. ...

    Bob from Canada was looking for a top end cover.

    Hal
  24. Replies
    12
    Views
    1,257

    You might check at Tony's lathes.co.uk There is...

    You might check at Tony's lathes.co.uk
    There is lots of info on that sight.
    Hal
  25. Matt looks like you did a great job. Hal

    Matt looks like you did a great job.

    Hal
Results 1 to 25 of 1253
Page 1 of 51 1 2 3 4