Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: karl

Page 1 of 11 1 2 3 4

Search: Search took 0.00 seconds.

  1. We've all seen far worse. If you adjust the...

    We've all seen far worse. If you adjust the clearances, keep them well oiled and don't run at higher speeds you should be able to do surprisingly good work with what you have. That being, said...
  2. Thread: mill in a corner

    by karl
    Replies
    51
    Views
    3,318

    I used to feel the same then forgave her.With...

    I used to feel the same then forgave her.With that burden off my back it doesn't hurt as much.
  3. Thread: South Bend parts

    by karl
    Replies
    6
    Views
    453

    May I suggest that you try EBAY?

    May I suggest that you try EBAY?
  4. Thread: Unknown tools

    by karl
    Replies
    10
    Views
    1,061

    #1 chipper blades for dados #2 looks like a tool...

    #1 chipper blades for dados
    #2 looks like a tool a MD would use to look up your nose
    #3 tubing bender
  5. Thread: OT: Flashlights

    by karl
    Replies
    55
    Views
    3,528

    First, many thanks to all of you that posted....

    First, many thanks to all of you that posted. While continuing my search I came across just what I was looking for: Energizer EPMZH21E.A double A made of metal with the switch in the correct spot. No...
  6. Go to youtube and look up either Tyrrell's Garage...

    Go to youtube and look up either Tyrrell's Garage or Harry's garage one of them recently did something. If I remember correctly they had to get custom pistons from a US supplier. Just a side note,...
  7. Thread: OT: Flashlights

    by karl
    Replies
    55
    Views
    3,528

    OT: Flashlights

    Do you remember when flashlights had switches in the correct location? You would pick up a flashlight and the switch would be right under your thumb ready to be slid or pushed to do your bidding. I...
  8. Replies
    57
    Views
    3,630

    The best advice I ever received:"Little pigs get...

    The best advice I ever received:"Little pigs get fat, fat pigs get slaughtered"
    Karl
  9. Replies
    5
    Views
    481

    Contact Long Island Indicator

    Contact Long Island Indicator
  10. I don't have a Kellogg but a Quincy 308. The...

    I don't have a Kellogg but a Quincy 308. The original manual says engine oil is OK if the service is not severe.
    Karl
  11. Replies
    5
    Views
    1,164

    PM sent. Thanks.

    PM sent. Thanks.
  12. Replies
    35
    Views
    5,259

    How about having them spun?

    How about having them spun?
  13. Replies
    11
    Views
    1,962

    I have a Phase II and I'm quite pleased with it....

    I have a Phase II and I'm quite pleased with it. If I had it do do over I would pick a wedge type. Look on Ebay lots to pick from.
    Karl
  14. Replies
    23
    Views
    4,015

    I just measured mine and it was 0.924".

    I just measured mine and it was 0.924".
  15. Just a guess, but when Uncle Mao stole the plans...

    Just a guess, but when Uncle Mao stole the plans that's what was indicated and they reasoned that if the Round Eyes made them that way so will we.
    Karl
  16. Replies
    16
    Views
    2,421

    I worked for the Dept. of Defense for 40 years as...

    I worked for the Dept. of Defense for 40 years as an electronics tech and we used plastics and aluminum, sometimes in combination, if the traces were too close to the stand offs so that they would...
  17. Allow me to split a hair or two, but the Volvo...

    Allow me to split a hair or two, but the Volvo you are referring to is an 1800ES other than that you're spot on.
    Karl
  18. Replies
    4
    Views
    1,432

    Thanks to all of you for your help. I started...

    Thanks to all of you for your help. I started with a HSS rougher and then switched to carbide which worked a treat.
    Karl
  19. Replies
    4
    Views
    1,432

    Silver solder paste

    I recently acquired an old filing machine that had a badly worn guide. I made a "patch" and took it to a local shop to have it brazed and they suggested welding as it would be faster and less...
  20. Replies
    1
    Views
    785

    The company is still open in Sweden, drop them an...

    The company is still open in Sweden, drop them an email.
    Karl
  21. Find/make a flat washer the same OD as the pipe...

    Find/make a flat washer the same OD as the pipe and put it in the rubber foot first.
    Karl
  22. Replies
    6
    Views
    1,675

    Very OT, but are you a tube amp buff (KT88)? Karl

    Very OT, but are you a tube amp buff (KT88)?
    Karl
  23. Replies
    3
    Views
    827

    Bore out the gear and make a bushing to fit. Karl

    Bore out the gear and make a bushing to fit.
    Karl
  24. Replies
    25
    Views
    4,823

    There is at least one member of this forum that...

    There is at least one member of this forum that sells these on ebay.
    Karl
  25. Try Garber Metrology, 1-800-427-3032. They are in...

    Try Garber Metrology, 1-800-427-3032. They are in the York, PA. area, there was no address on the cert. label but you should be able to GOOGLE them.
    Karl
Results 1 to 25 of 258
Page 1 of 11 1 2 3 4