Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: xa-mont

Page 1 of 25 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    40
    Views
    3,643

    on the machine with EIA enabled, what is the...

    on the machine with EIA enabled, what is the version on it? is it C0 like on that ROM?
  2. Replies
    40
    Views
    3,643

    Just did some more googling and it seems the...

    Just did some more googling and it seems the MC455-1 is the board with the add in disk/card things.

    On my machine that's the MC151.

    Have you tried just swapping the addon cards?
  3. Replies
    40
    Views
    3,643

    Well that's some good info - interestingly my...

    Well that's some good info - interestingly my T32-6 doesn't appear to have either a 116 OR a 455-1. I have a slot marked MC116, but the board in there is labeled MC446-1 (but it's got different...
  4. Replies
    40
    Views
    3,643

    Have you tried swapping your mc419 as well? ...

    Have you tried swapping your mc419 as well?

    Sent from my G8141 using Tapatalk
  5. Replies
    40
    Views
    3,643

    My eprom reader rocked up today, so i'll give...

    My eprom reader rocked up today, so i'll give mine a read. and if you could do the same Bengt so we can compare the 2 that would be awesome.
  6. Replies
    40
    Views
    3,643

    so i just tried the write to EEPROM thing, but...

    so i just tried the write to EEPROM thing, but only changed O14 bit 3 (which seemed to enable the sync tapping option). it didn't stay after turning off and on, so there must be something else to the...
  7. Replies
    40
    Views
    3,643

    So i just spoke to a mate about this who was a...

    So i just spoke to a mate about this who was a mazak tech from way back, and he said he reckons the lower option parameters couldn't be changed - he said it actually reads them at startup from a ROM....
  8. Replies
    40
    Views
    3,643

    are the pictures visible now?

    are the pictures visible now?
  9. Replies
    40
    Views
    3,643

    I'll fix it when I get home Sent from my G8141...

    I'll fix it when I get home

    Sent from my G8141 using Tapatalk
  10. Replies
    40
    Views
    3,643

    you might be onto something there Bengt. ...

    you might be onto something there Bengt.

    Here's my diag screen (with op19 set to 33 so that EIA comes up.)

    272919

    and this is my mem card.
    272920
  11. Replies
    40
    Views
    3,643

    some small progress i made just now! so I KIND...

    some small progress i made just now!

    so I KIND OF got EIA happening on my machine, at least i made it look like it's there temporarily.

    It would appear that OP19 bit 1 enables the EIA option...
  12. Replies
    40
    Views
    3,643

    BUMP just in case anyone has any more info to add.

    BUMP just in case anyone has any more info to add.
  13. Thread: English T32

    by xa-mont
    Replies
    6
    Views
    653

    for reference here's my MC419 ...

    for reference here's my MC419
    ...
  14. Thread: English T32

    by xa-mont
    Replies
    6
    Views
    653

    I might be able to help you out. i don't have an...

    I might be able to help you out. i don't have an eprom reader, but i'm thinking about getting one. I really want to work out how to add EIA to my T32. What sort of reader should i get?
  15. Replies
    6
    Views
    907

    I may have actually found a cheaper solution (for...

    I may have actually found a cheaper solution (for what i'm wanting to achieve).

    My brother is a programmer/software engineer that does a lot of things with motion tracking and VR etc. anyway i was...
  16. Replies
    6
    Views
    907

    I've just stumbled across a mob called Deva that...

    I've just stumbled across a mob called Deva that does PCI or USB interface cards. I've sent them an email to see what they have to say about my specific case.

    Deva Electronics - Manual CMM...
  17. Replies
    6
    Views
    907

    Sweet. I'll look into it. Being before your time...

    Sweet. I'll look into it. Being before your time I would assume you don't, but have you got any idea if the retrofit required replacing scales or anything like that? or is it just some sort of...
  18. Replies
    6
    Views
    907

    Hansford rapid check

    Hey guys,

    Just won this bad boy at auction:
    https://www.graysonline.com/lot/3008-3016547/mechanical-workshops/rapid-check-3-axis-measuring-machine?redirect=0

    It's a Hansford rapid check...
  19. Replies
    0
    Views
    298

    M2 VQC20/40 spindle speed dips?

    Hey everyone,

    I've always gotten these little blips of rev drop, which isn't a massive deal, but if there's a few blips together on a high load operation it'll drop the revs further and possibly...
  20. have you tried reversing the phasing on your...

    have you tried reversing the phasing on your incoming wiring? you may have the phasing wrong, which in turn will spin the hydraulic pump backwards.
  21. Thread: Fjv25 m+

    by xa-mont
    Replies
    0
    Views
    393

    Fjv25 m+

    hey guys,

    I'm currently making inquiries about an M+ FJV-25 with a pallet changer. (Used mazak FJV 25 CNC Machining Centre in Acacia RIdge, QLD Price: $49,500)

    firstly, is there anything...
  22. Replies
    3
    Views
    486

    i've also noticed when it faults to this state,...

    i've also noticed when it faults to this state, it will be showing all the LED's as soon as i hit the on button - in the other state it looks fine until the drives try to power up (i assume that's...
  23. Replies
    3
    Views
    486

    sometimes it'll come up in this fault state as...

    sometimes it'll come up in this fault state as well. with it in this state i can press the reset hardware button on the board and it will then show a normal state, but the machine is still faulted...
  24. Replies
    6
    Views
    657

    have you got the transformer tapped correctly for...

    have you got the transformer tapped correctly for 240v?
  25. Replies
    6
    Views
    657

    could be the screen not working. try home the...

    could be the screen not working. try home the machine (lever to x neg and z neg if it already up near the home position) This will show you if the machine is "ON" and the screen just isn't working
    ...
Results 1 to 25 of 603
Page 1 of 25 1 2 3 4