Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Cole2534

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    15
    Views
    525

    Haha. If you don't ID grind and air gauge the...

    Haha. If you don't ID grind and air gauge the clearance holes on a bridge girder you aint a real 'chinist.

    Sent from my SM-G973U using Tapatalk
  2. Replies
    15
    Views
    525

    No worries dude. Some guys hear oilfield and...

    No worries dude. Some guys hear oilfield and assume you're making drill collars or the like without considering that DH tools come in all sizes.

    Sent from my SM-G973U using Tapatalk
  3. Replies
    3
    Views
    149

    I haven't yet, PM is my first stop for all things...

    I haven't yet, PM is my first stop for all things machining.

    If no one has an answer here before I get back to my desk I'll ask over there and relay the message.
  4. Replies
    3
    Views
    149

    Fusion360 adding small lines randomly

    Without reason, I'll find that Fusion360 has added a small line to a line I've sketched and it's infuriating. Has this happened to anyone else? If so what's the solution?

    Imagine- you draw a...
  5. A single random of pipe should be 20+ ft. Sent...

    A single random of pipe should be 20+ ft.

    Sent from my SM-G973U using Tapatalk
  6. Replies
    13
    Views
    3,303

    But if someone finds it again I'd like to know. ...

    But if someone finds it again I'd like to know.

    Sent from my SM-G973U using Tapatalk
  7. Replies
    85
    Views
    2,910

    There hasn't been peace on earth since the...

    There hasn't been peace on earth since the population exceeded 1.
  8. Replies
    9
    Views
    488

    Concur. Also much preferred to the gas axe for...

    Concur. Also much preferred to the gas axe for general severing of other things around the shop.
  9. Agreed. All you need is a test light to decipher...

    Agreed. All you need is a test light to decipher which is which.
  10. Replies
    52
    Views
    4,123

    I'm lucky. I have an Airgas 1/2mi from my shop...

    I'm lucky. I have an Airgas 1/2mi from my shop and per the store mgr, it is one of the highest foot traffic'd sites in the state- ie, they carry a lot of stuff in stock.
  11. Replies
    52
    Views
    4,123

    I almost went that route, but I figured the C25...

    I almost went that route, but I figured the C25 was a more flexible gas so I could try other wires as well.
  12. Replies
    52
    Views
    4,123

    Swung by my buddies shop and he gave me a spool...

    Swung by my buddies shop and he gave me a spool of .045" ESAB 7100 Ultra and it ran really smooth with C25. It had a high deposition rate and ran with less smoke, very little spatter and smooth bead...
  13. Replies
    16
    Views
    890

    Good looking wire, but my machine maxes out right...

    Good looking wire, but my machine maxes out right around the min voltage req's. I'm going to try some .045" UltraCore 71A75.
  14. Replies
    52
    Views
    4,123

    A pain in the ass, but not insurmountable. Spool...

    A pain in the ass, but not insurmountable. Spool some onto a sub-spool, then vac/dessicant pack the remainder. And if you're doing a big job install the full spool.

    I'll give it a go.
  15. Replies
    52
    Views
    4,123

    Loving this 256 but the spatter and smoke of the...

    Loving this 256 but the spatter and smoke of the NR-221 has to go. The minimum quantity of the wire I want to run (.045" Lincoln UltraCore 71A75) is 33lb which will last a while unless it's going to...
  16. Replies
    16
    Views
    890

    Josh, I've been wanting to try some D/S wire in...

    Josh, I've been wanting to try some D/S wire in my PowerMig256 for lightish weldments in the 1/8-1/4" thick range.

    What wire would you suggest?
  17. Yes, an esoteric gesture rather than a billboard.

    Yes, an esoteric gesture rather than a billboard.
  18. Replies
    19
    Views
    1,231

    Well, PM got me again and now I uave one of those...

    Well, PM got me again and now I uave one of those Eastwood scroll units on the way. I'll report back.

    The reviews on Garage Journal seemed fair, but that site seems like a bunch of bickering old...
  19. This would certainly be a manual process and not...

    This would certainly be a manual process and not intended for every member that passes, as such I feel the overall volume would be low enough to not be burdensome.

    RJ Newbold is another that, IMO,...
  20. Replies
    81
    Views
    7,466

    I'm terribly sorry to hear this. Admin- is...

    I'm terribly sorry to hear this.

    Admin- is there a way to change someone's status from Diamond or whatever to something else that would commemorate them as a passed contributor of significance?
    ...
  21. Seems reasonable to me! Sent from my...

    Seems reasonable to me!

    Sent from my SM-G973U using Tapatalk
  22. I was wondering the same thing, how the hell...

    I was wondering the same thing, how the hell they're gonna do that in a timely a predictable fashion?

    Moonlight does work on some fancy car stuff tho, typical time and money constraints don't...
  23. Replies
    51
    Views
    6,843

    Thanks for the followup. I was looking at one of...

    Thanks for the followup. I was looking at one of their products this week and it made me wonder what became of it.

    Sent from my SM-G973U using Tapatalk
  24. Replies
    8
    Views
    923

    I must acquire this. Anyon have a spare they...

    I must acquire this.

    Anyon have a spare they wanna sell before I spring for a new one?

    Sent from my SM-G973U using Tapatalk
  25. Replies
    37
    Views
    2,179

    Good catch, I'd amend my post but it won't let me.

    Good catch, I'd amend my post but it won't let me.
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4