Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: windsormw

Page 1 of 7 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    28
    Views
    1,997

    1. Set up some traps with bait but be sure not...

    1. Set up some traps with bait but be sure not to arm them .

    2. Replenish bait daily for 7 days

    3. On the 8th day bait and arm all traps …..

    Continue this routine as needed
  2. Replies
    6
    Views
    931

    " Id like to set up a closed loop servo drive and...

    " Id like to set up a closed loop servo drive and need some ideas please "

    That course , as informative as it is ... does not specify much in the department of PLC servo control. Assuming I...
  3. Replies
    6
    Views
    931

    My employer deals with Allen Bradley old and new...

    My employer deals with Allen Bradley old and new , but thanks
  4. Replies
    6
    Views
    931

    PLC simulator ideas

    gentlemen ......

    Id like to be clear . I'm a millwright with zero programing experience , relay logic skills are effective but not superior . Industrial control has always fascinated me , megabits...
  5. Doing the work myself , in frame . Not sure how...

    Doing the work myself , in frame . Not sure how long the previous silicone lasted , had this tractor for a couple years . I'm talking about a machine in good working order .

    The amount of pull...
  6. Question : Rebushing wet liner seal surfaces

    Good morning ,

    I have a very old Case 680 ck ( b ) tractor backhoe which these days is rare but until now has always been in good working order .

    The cast machined surfaces of the engine...
  7. Replies
    1
    Views
    656

    30 hp rpc questions

    I have built a 10 hp finch Williams model some time ago and have been very pleased so far .

    As luck would have it , I have purchased some new to me machines that will be too much for my rpc to...
  8. Bridgeport z knee ball screw recommendations

    Have most of the parts rounded up to power the knee via cnc .

    I have been looking on ebay , don't know much about ball screw manufacturer reputation for quality etc...

    Please chime in .
    ...
  9. Replies
    1
    Views
    1,268

    Fusion 360 and windnc

    As a novice cnc operator and with budget in mind .

    Can anyone tell me if it is possible to interface the free version on fusion 360 , windnc and my old fagor 8040 m ?

    Thanks
  10. Replies
    5
    Views
    1,655

    It's a conversational controller Thanks

    It's a conversational controller

    Thanks
  11. Replies
    5
    Views
    1,655

    Fagor 8040 help

    I have a 2 axis cnc knee mill gentlemen . I also know very little about cnc but the time has come ( or so I am telling myself ) to learn how to use it .

    I have a customer that needs a circular...
  12. Replies
    9
    Views
    2,123

    The box below transformer has got the on delay...

    The box below transformer has got the on delay relay and motor starter in it. It also controls pendent at 24vdc.

    I rounded up some new start caps today. They are half the size yet have the same...
  13. Replies
    9
    Views
    2,123

    My fw ( ugly wiring job) rpc has ran for years. ...

    My fw ( ugly wiring job) rpc has ran for years. Worked really well, the start problems had only begun when I wired the transformer direct to rpc.
    Transformer is now disconnected, rpc will not...
  14. Replies
    9
    Views
    2,123

    http://img.photobucket.com/albums/v720/windsormw/M...

    http://img.photobucket.com/albums/v720/windsormw/Mobile%20Uploads/DSC_0069_zpsyifmgghz.jpg

    I'm using the pdf download of the fw rpc schematic avaliable in this section.


    I know the wiring is a...
  15. Replies
    9
    Views
    2,123

    http://img.photobucket.com/albums/v720/windsormw/M...

    http://img.photobucket.com/albums/v720/windsormw/Mobile%20Uploads/1459564354704_zpsmspynj2m.jpg


    I've tested all caps with a micro Farad meter. Everything checks out......... Run and start...
  16. Replies
    9
    Views
    2,123

    I checked all caps with ohm meter . They all...

    I checked all caps with ohm meter . They all seem fine but I dont have the uf setting on my meter .

    Machine is reciving 240 vac , I tightened ever terminal inside rpc and both starters are...
  17. Replies
    9
    Views
    2,123

    i need 600 for a cnc mill but also need 240 3...

    i need 600 for a cnc mill but also need 240 3 phase for other machines . I am supplying rpc with 240vac single phase .

    my rpc has worked fine for years producing 240 3 phase .
  18. Replies
    9
    Views
    2,123

    rpc start circut problems

    I recently wired a 15 kva 240/600 to my FW RPC . To my surprise I learned that their had to be a switch between the rpc and transformer .

    I have dissconnected the transformer and now my rpc will...
  19. thats exactly what I needed to know , Thanks...

    thats exactly what I needed to know ,

    Thanks PM , I'll give it a shot as soon as i scare up some more parts .


    Scott
  20. It's 10 HP. No machines are on during start up....

    It's 10 HP. No machines are on during start up. My rpc has worked fine for years.

    Are you saying the transformer is drawing a big enough load to prevent the rpc from starting and closing a set...
  21. It buzzes and will not build rpms

    It buzzes and will not build rpms
  22. Wired rpc to 600 transformer.......... Issues

    Hello Pm

    I have a Finch Williams rpc, built it myself and recently wired a 15 kva 240\600 transformer.

    The hook up seemed straight forward but perhaps I've over looked something. I wired...
  23. Replies
    54
    Views
    7,762

    the ways are badly worn , The taper is never...

    the ways are badly worn ,

    The taper is never consistent and long cuts are in and out like a fiddlers elbow .

    thanks everyone
  24. Replies
    0
    Views
    766

    magnum cut cnc knee mill ?

    I am looking at one just never heard of the manuf. before . It has FAGOR 8040 CNC CONTROLS and is 2 axis cnc .


    MILLERS: 12" x 54", MAGNUM-CUT FM-5V, CNC VERTICAL MILLING MACHINE

    looks just...
  25. Replies
    54
    Views
    7,762

    thanks for all the folks on this board that...

    thanks for all the folks on this board that commented and helped me along the way.

    Diagnosis.... It's worn out !

    I have checked and measured and checked again - compared data and wa-la !...
Results 1 to 25 of 163
Page 1 of 7 1 2 3 4