Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: digger doug

Page 1 of 60 1 2 3 4

Search: Search took 0.11 seconds.

  1. Boat or car ?.....:D

    Boat or car ?.....:D
  2. Replies
    133
    Views
    8,186

    Smokey and the Bandit (9/10) Movie CLIP - The...

    Smokey and the Bandit (9/10) Movie CLIP - The Snowman Is Comin' Through (1977) HD - YouTube
    :D

    Need to lighten up the room a wee bit....:crazy:
  3. Replies
    10
    Views
    394

    What would an off the shelf 20kw genset cost ? ...

    What would an off the shelf 20kw genset cost ?

    EDIT:
    20-29 kW Commercial Standby Generators - Electric Generators Direct
  4. Replies
    10
    Views
    394

    What did they design that engine to run at ?

    What did they design that engine to run at ?
  5. Replies
    24
    Views
    1,610

    Couple that with some sawhorse's or a table made...

    Couple that with some sawhorse's or a table made for blade clearance and that keeps supporting after the cut, to complete the kit.
  6. Replies
    10
    Views
    394

    It was a good idea, it was implemented...

    It was a good idea, it was implemented badly....very badly.

    My friend the pipeline welder had one, it let him down so many times (many hours from home) he traded for a Lincoln.

    That led me to...
  7. "pass thru" like several times a day ??? ...

    "pass thru" like several times a day ???

    Again, simple blob of silicone sealant/glue will doo nicely.....
  8. Replies
    21
    Views
    1,571

    Where did I go wrong in my post sir ?

    Where did I go wrong in my post sir ?
  9. Some coolant pumps don't have seals.

    Some coolant pumps don't have seals.
  10. Replies
    21
    Views
    1,571

    There are used car dealers around here that...

    There are used car dealers around here that specialize in bringing up cars from the "Rust free south" as they don't get any salt damage.

    I'm not doubting you, but I can't fathom how Ozzland...
  11. Replies
    21
    Views
    1,571

    I see all kinds of rust on vehicles around here...

    I see all kinds of rust on vehicles around here ..... but Ozzland ?????
  12. Replies
    124
    Views
    7,032

    Yes, I know all about that process, and it's...

    Yes, I know all about that process, and it's limitations.

    Hence I did NOT suggest it, rather someone would develop a coating, without all the problems and cost's with the above system.
  13. Replies
    124
    Views
    7,032

    If the money is there, some one will get a...

    If the money is there, some one will get a coating process up and running.

    Shut down a street, pump in some plastic sealer, go to each house and run the main tap until material comes out clean.
    ...
  14. Thread: Student

    by digger doug
    Replies
    5
    Views
    685

    Please take qty (5) minutes and read the stickies...

    Please take qty (5) minutes and read the stickies up top about a proper title.
  15. Replies
    11
    Views
    1,349

    "my lathe" ....Please explain more.

    "my lathe" ....Please explain more.
  16. Replies
    32
    Views
    2,431

    Look at what a W&S automatic uses on the turret.

    Look at what a W&S automatic uses on the turret.
  17. Replies
    4
    Views
    928

    Craigslist is the place for you....

    Craigslist is the place for you....
  18. Replies
    21
    Views
    1,571

    Timbren or some one else makes an air ride...

    Timbren or some one else makes an air ride trailer axle assembly (actually there is no axle, just a stub on each side)

    They would be the best to advise you on your question.

    FWIW, air ride semi...
  19. Replies
    41
    Views
    2,497

    Doesn't your bushing use shims ? Make the...

    Doesn't your bushing use shims ?

    Make the bushing keyway deeper so that you take a smaller initial cut, shim and take additional passes as needed.
  20. Replies
    41
    Views
    3,269

    "Truck mounted VMC" now that could be the start...

    "Truck mounted VMC" now that could be the start of a Haas adverting campaign.
  21. What hardness does the finished product need ?

    What hardness does the finished product need ?
  22. Replies
    13
    Views
    2,858

    Still no pix of the actual machine ?

    Still no pix of the actual machine ?
  23. Replies
    15
    Views
    1,335

    Here you go: Making a BIG LATHE from SCRATCH,...

    Here you go:
    Making a BIG LATHE from SCRATCH, using only basic tools - YouTube

    You'll note the use of everyone's favorite, a 'Treadmill Motor" as well.


    Try over at "the zone" please.
  24. Thread: Big Score

    by digger doug
    Replies
    7
    Views
    1,434

    What's the loss if this whole thread get's...

    What's the loss if this whole thread get's deleted/lost ?
  25. Replies
    24
    Views
    4,652

    Why are you posting this in some other,...

    Why are you posting this in some other, unrelated, old thread ?
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4