Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: rakort

Page 1 of 15 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    10
    Views
    2,675

    one more input from the community. I do have a...

    one more input from the community. I do have a hole in the bottom of my RD apron into the sight glass bore.

    278677
  2. Replies
    10
    Views
    540

    flip all those pieces over and take another...

    flip all those pieces over and take another picture please
  3. Replies
    4
    Views
    335

    No problem, let us know how it works out. I...

    No problem, let us know how it works out.

    I guessed at the 60" length......figured it was long enough though.
  4. Replies
    4
    Views
    335

    McMaster-Carr (https://www.mcmaster.com/1497k34)

    McMaster-Carr
  5. Replies
    5
    Views
    434

    Agreed, after I thought about it a minute the...

    Agreed, after I thought about it a minute the coarse screen is to support the felt/filter.
  6. Replies
    5
    Views
    434

    In my head I would go from the outside to the...

    In my head I would go from the outside to the inside with coarse screen, fine screen, felt. Get the rocks out first, then the sand, then the silt.
  7. Replies
    15
    Views
    1,151

    Not sure what is up.... You called it a...

    Not sure what is up....

    You called it a spacer. I believe Monarch calls it a deflector. I call it a flinger. That spacer is for flinging the oil that works its way through the bearings outward...
  8. Replies
    23
    Views
    3,747

    I found this sometime ago around here 275594

    I found this sometime ago around here

    275594
  9. Replies
    15
    Views
    1,151

    you can see in my picture (also from a round...

    you can see in my picture (also from a round dial) that it has the same bearings.

    I'm thinking the AC bearings were from a newer iteration of the gearbox design.

    As I recall I had a hard time...
  10. Replies
    15
    Views
    1,151

    I'm sure you cleaned out the oil drain back port...

    I'm sure you cleaned out the oil drain back port from outside the outer bearing, set the snap ring properly, and didn't cover it with a gasket, right?

    275119
  11. Replies
    23
    Views
    3,747

    I missed it initially......this thread died and...

    I missed it initially......this thread died and then jumped ahead 2 years....ooops.

    Vette dude are you still out there?
  12. Replies
    23
    Views
    3,747

    I'm all in for a clamp. Mark me down Are you...

    I'm all in for a clamp. Mark me down

    Are you making these for a round dial, square dial, or both? I understand the clamps are different. I'm interested in a round dial variety.
  13. Replies
    13
    Views
    1,013

    Electrical Schematic EE-2674 10EE SN 19377...

    Electrical Schematic EE-2674 10EE SN 19377
  14. Replies
    13
    Views
    1,013

    Couldn't make it to the end of this....was there...

    Couldn't make it to the end of this....was there a point in there some place?
  15. Replies
    13
    Views
    1,013

    Be warned. As Cal pointed out to me, Monarch...

    Be warned. As Cal pointed out to me, Monarch will offer only a "generic" documentation package for a round dial machine. They will have the original Machine SN card with the as delivered specs, but...
  16. Radwell has dug us out of more than one shit...

    Radwell has dug us out of more than one shit mess, but can't quite comprehend why buying a simple 10ee brush set would be put to them when they are easily available from the oem and likely else...
  17. Replies
    13
    Views
    1,013

    Is this an inline exciter? Can you share a pic...

    Is this an inline exciter? Can you share a pic of your MG drive unit?

    I've got reasonable copies of EE2442 (but not 2452) Can you verify the drawing #
  18. Replies
    102
    Views
    6,969

    Agreed, remove and tear down the apron and put it...

    Agreed, remove and tear down the apron and put it back in tip top shape. It is a task, but a must do service that probably is necessary unless for some magical reason the sump on the bottom of the...
  19. Replies
    102
    Views
    6,969

    Me too! Nice work on the inspection. The ways...

    Me too! Nice work on the inspection. The ways look much better than that first picture suggested. I'm not quite sure why but I would have guessed based on the picture there was some +10 thou worn...
  20. Yes they are still in existence. Last I heard...

    Yes they are still in existence. Last I heard they will also sell you a factory top to bottom refurb square dial 10EE for ~ $200,000.
  21. Replies
    10
    Views
    1,267

    And me after you!

    And me after you!
  22. Parts | Monarch Lathes...

    Parts | Monarch Lathes

    Monarch will fix you up.
  23. Replies
    102
    Views
    6,969

    I'll also add, some wise person in this forum...

    I'll also add, some wise person in this forum once said, if you can hook your fingernail on a "lip" on the backside of the bed's front V-Way then you should probably walk away.

    With that said,...
  24. Replies
    102
    Views
    6,969

    I agree with most that this seems to be a well...

    I agree with most that this seems to be a well maintained or likely a "cleaned up" lathe. I'm sure a buyer can't go too far wrong for the the right price. I've taken pause however on what seems to...
  25. Replies
    6
    Views
    675

    that is "new height" or square dial steady rest.

    that is "new height" or square dial steady rest.
Results 1 to 25 of 373
Page 1 of 15 1 2 3 4