Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: TDegenhart

Page 1 of 60 1 2 3 4

Search: Search took 0.05 seconds.

  1. There may be a problem with the enterlock if the...

    There may be a problem with the enterlock if the breaker was in the off position. Some may require that the handle be moved to the reset position for it to be disabled.

    Tom
  2. I take it from your absence of a reply that the...

    I take it from your absence of a reply that the additional pins was ridiculous. Ok, since we are brain storming, put cam blocks on the hot side plate that engages the cavity plate (do I have that...
  3. Replies
    12
    Views
    635

    I use the paper trick, then ease the wheel down...

    I use the paper trick, then ease the wheel down until I scratch layout or magic marker. Tom
  4. We called them pecker pins. So add two more...

    We called them pecker pins. So add two more pins.

    Tom
  5. Replies
    5,185
    Views
    783,787

    I'll bite, what is banda_precision? Tom

    I'll bite, what is banda_precision?

    Tom
  6. Replies
    17
    Views
    918

    Bigger catch basin and a oil filter and...

    Bigger catch basin and a oil filter and recirculate system. Bast of both worlds.

    Tom
  7. Not a mold builder, but what strikes me as a...

    Not a mold builder, but what strikes me as a solution is a pancake cylinder of the same diameter as the lock cylinder positioned to be in alignment with the opposite lock cylinder. Put the cylinders...
  8. If you want accuracy use a sine plate. Tom

    If you want accuracy use a sine plate.

    Tom
  9. Replies
    11
    Views
    1,178

    As a customer I wouldn't care what the media...

    As a customer I wouldn't care what the media looks like, I would want to know what the finished part would be like.

    Tom
  10. Replies
    18
    Views
    2,114

    I thought the monsters were the ones where the...

    I thought the monsters were the ones where the operator rode in a carriage attached to the saddle.

    Tom
  11. By no means. You would just have to have a logic...

    By no means. You would just have to have a logic controller that senses voltage and phase angle of the generated leg, that as conditions change, be able to switch in and out balancing capacitors and...
  12. Your not married with kids are you? Tom

    Your not married with kids are you?

    Tom
  13. What do you need a fuel pump for? Gravity feed....

    What do you need a fuel pump for? Gravity feed.

    Tom
  14. Replies
    19
    Views
    1,167

    I concede to 29.6.1 for POWER wire and yes, the...

    I concede to 29.6.1 for POWER wire and yes, the opening statement was about 8 and 10 ga. I was thinking about the control wire. The next point is for field wiring (customer) connectors. Here the...
  15. I agree with kk, from your description, its one...

    I agree with kk, from your description, its one rust spot chasing another. Heating will not clean out the rust. In this case you probably will need to cut away all the rust and replace with good...
  16. Replies
    19
    Views
    1,167

    I don't believe U/L has anything to say in this...

    I don't believe U/L has anything to say in this area. They go by temperature tests. The old JIC standards did require a minimum of 14 ga, but that is the only one I am aware of. I don't think I...
  17. Replies
    1
    Views
    239

    Connect it to 240 and see how it operates. Check...

    Connect it to 240 and see how it operates. Check the motor current.

    Tom
  18. Out of curiosity, how does the classic solid...

    Out of curiosity, how does the classic solid base/jaw Bridgeport vise work?

    Tom
  19. Replies
    30
    Views
    2,251

    Quite honestly, I have never seen a motor fail...

    Quite honestly, I have never seen a motor fail from loose laminations, or for that matter loose windings. For a motor to be U/L listed for class H or other high temperature insulation systems, not...
  20. A solution to this problem I have found is that...

    A solution to this problem I have found is that the stationary jaw is more rigid than the moving or can be made so. Register the work against the stationary jaw and vice bed, then place something...
  21. Replies
    25
    Views
    1,568

    What you find objectionable about TL-1? Tom

    What you find objectionable about TL-1?

    Tom
  22. Replies
    19
    Views
    1,167

    By automatic ferruling machine, is this one the...

    By automatic ferruling machine, is this one the cuts, strips the insulation and assembles the ferrule? Is there room for two ferrules in a saddle clamp termination? Ring and spade terminates are...
  23. Replies
    19
    Views
    1,167

    First to look for, are the ferrules U/L or equal...

    First to look for, are the ferrules U/L or equal listed or recognized? So long as the ferrule is properly assembled per the instructions, it should be just fine. The only advantage that I see is...
  24. Replies
    25
    Views
    1,568

    How does a lathe chuck fit into the Samchully...

    How does a lathe chuck fit into the Samchully company. Best I can determine they are an energy company. Is this a part of an acquisition that will be spun off?

    Tom
  25. Replies
    109
    Views
    5,939

    Part of that is that the more they invade our...

    Part of that is that the more they invade our domain, the more action we take. Flies, mice, rats and such bring diseases and, in the case of mice and rats, destruction. Squirrels less so, with...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4