Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: russler

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    561

    I'm waiting for the rack cutter to come up, I...

    I'm waiting for the rack cutter to come up, I already have US to Oz sorted, Alaska to the lower 48 to work out.If your interested in shipping together, send me a PM
    Russell
  2. Number 2 dial type is 6 1/8" centre of spindle to...

    Number 2 dial type is 6 1/8" centre of spindle to bottom of overarm. Number 3 & 4 are 7 3/8"
    Hope this helps.
    I would be interested in the Rack cutter.
  3. FWIW try Loctite "super wick in" around the seam....

    FWIW try Loctite "super wick in" around the seam. I recon that it will give you a few more years. Make sure it's dry first.
  4. Replies
    7
    Views
    1,159

    FWIW, a number 2 drive gear is 5.3" OD, has 28...

    FWIW, a number 2 drive gear is 5.3" OD, has 28 teeth and is 1.5" wide.
    The back of the gear is 1.4" from the column face.
    The driven gear is about 3.7" OD and has 19 teeth.
    Hope this helps.
  5. Replies
    48
    Views
    5,248

    Have a look at an older marine reduction box.The...

    Have a look at an older marine reduction box.The old dog clutch type. 1.52:1 rings a bell, that would be close to what you're looking for.
  6. Replies
    53
    Views
    4,068

    International made a 152 ci 4 cylinder out of a...

    International made a 152 ci 4 cylinder out of a 304 ci V8. Used in the early Scout and some Ag. equipment.
    Holman made a 60 cu ft compressor by converting 2 cylinders of a VW.
  7. Replies
    13
    Views
    1,560

    4 hours and counting

    4 hours and counting
  8. Replies
    9
    Views
    1,046

    Just had a chance to measure, 15 degrees from...

    Just had a chance to measure, 15 degrees from axis or 30 included.
    The die is about (bit hard to measure as the top edge is rounded) 4.338"at the top (large end of taper). The die ring, silver is...
  9. Replies
    9
    Views
    1,046

    About 15 degrees

    About 15 degrees
  10. Replies
    38
    Views
    5,216

    I don't see anything wrong with the way it's...

    I don't see anything wrong with the way it's chained, it's on wheels, so you try and chain long and flat to stop the chain "snaching",cross chain so it can't move side ways, long ways so it can't...
  11. Replies
    28
    Views
    8,200

    Joe, your probably right, but the point I make is...

    Joe, your probably right, but the point I make is that a full lenth thread will probably pick up enough thread to be secure keeping in mind that the filter only uses 4 or 5 threads.

    Russell
  12. Replies
    28
    Views
    8,200

    There still seem's to be about 50% of the thread...

    There still seem's to be about 50% of the thread left, if an adaptor was made so that the filter seal was moved out more than the stud is long, an internal thread to screw onto the damaged stud, a...
  13. Replies
    28
    Views
    8,200

    There still seem's to be about 50% of the thread...

    There still seem's to be about 50% of the thread left, if an adaptor was made so that the filter seal was moved out more than the stud is long, an internal thread to screw onto the damaged stud, a...
  14. Replies
    35
    Views
    4,256

    Maybe the Chinese are paying us back for all the...

    Maybe the Chinese are paying us back for all the bagging!
  15. Replies
    7
    Views
    2,293

    Long Tom, strange you asked this...

    Long Tom,
    strange you asked this today as i've just spent the day fitting the coolant pump off that dial type to my own.
    Randy kindly removed the pump and sent it over for...
  16. Replies
    10
    Views
    1,420

    PM sent bout #6

    PM sent bout #6
  17. Replies
    43
    Views
    13,391

    I received the coolant pump the other day, all...

    I received the coolant pump the other day, all worked out well in the end, many thanks for your help and the trouble you went to for me.
    It's a shame they broke the pump drive shaft in the junk...
  18. All the above and are you feeling lucky? First,...

    All the above and are you feeling lucky?
    First, work out how much the machine is worth and is it insured?
    Then get a price on a pump, 2-4 times the total oil capacity and a box of filters.
    Compare...
  19. Replies
    57
    Views
    10,562

    I'll throw my 2 bob's worth in Richard, I've been...

    I'll throw my 2 bob's worth in Richard, I've been wondering how I could get to attend a scraping class, but short of comming to the states, I could only imagine what a class would hold. Last night...
  20. Replies
    57
    Views
    10,562

    If I had known earlier I would have put my name...

    If I had known earlier I would have put my name down as I plan to be in Melbourne early in October. If you have a last minute cancellation, I maybe close by.
    I'm intrerested in a future class.
    ...
  21. Replies
    27
    Views
    4,624

    Better get 6 "o" ring strechers:D

    Better get 6 "o" ring strechers:D
  22. Replies
    31
    Views
    3,111

    + 1 for all the comments above,must say,I did...

    + 1 for all the comments above,must say,I did scratch my head a bit when I could'nt find "lathe" in the list.

    Russell
  23. Replies
    43
    Views
    13,391

    PM sent about the dial type. Russell

    PM sent about the dial type.

    Russell
  24. Replies
    19
    Views
    8,230

    If you value your inverter,keep the exhaust well...

    If you value your inverter,keep the exhaust well away and insulate the inverter from engine vibration.Inverters don't like carbon or vibration!
  25. Replies
    19
    Views
    8,230

    Running a lister slow,maybe not a good idea.Been...

    Running a lister slow,maybe not a good idea.Been there done that,you end up with flickering lights becauce of the power strokes ie.speed fluctuations.
    Use a 4 pole gen. and direct drive,don't think...
Results 1 to 25 of 51
Page 1 of 3 1 2 3