Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: cmike

Page 1 of 28 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    2
    Views
    316

    Check your private nessages.

    Check your private nessages.
  2. Replies
    2
    Views
    785

    I think that is a English made machine. Check...

    I think that is a English made machine. Check your drive on the pump and see if it's broken.
  3. Here are the years each attachments. 1944...

    Here are the years each attachments.

    1944 Manual Pub. No. M1375 - 1ea Spiral Milling Attachment, stamped on the housing is AEA1P1/35
    Manual Pub. No. M - 2459 1ea (new old stock)...
  4. Replies
    19
    Views
    3,507

    cmike

    no ! Drop the oil.. The hex head taper pin will break the head off if not careful . use a socket to take loose. work it back and forth.Take out all but a few bolts. put a four X four board under the...
  5. Replies
    51
    Views
    16,381

    use sheet metal screw

    use sheet metal screw
  6. Replies
    2
    Views
    1,055

    The Fives 800.934.9735

    The Fives 800.934.9735
  7. Replies
    2
    Views
    784

    Call Cincinnati, 800.934.0735 or Tom...

    Call Cincinnati, 800.934.0735 or Tom 313.382.5880, or [email protected]
  8. Replies
    19
    Views
    3,507

    dis regard the above quotes.

    dis regard the above quotes.
  9. Replies
    19
    Views
    3,507

    Feed dial will not come out of the knee that way....

    Feed dial will not come out of the knee that way. What i am saying is the 277 A set screw is out. put a long screw in the place of the set screw. Then you can go in with the shaft and it will go out...
  10. Replies
    26
    Views
    4,820

    cmike

    No I am not. I will check around;
  11. Replies
    19
    Views
    3,507

    This machine does not have the shear key and does...

    This machine does not have the shear key and does not have a front bracket. If your feeds don't work, you may have to drop the feed drive. What point are you at right now ?

    Regards,
  12. Replies
    19
    Views
    3,507

    This machine does not have the shear key and the...

    This machine does not have the shear key and the front bracket on this model does not come off. When you take 277A out, put a long screw of the same thread in the same spot. Then you can move gear...
  13. Replies
    19
    Views
    3,507

    The shaft on the feed dial does not come out...

    The shaft on the feed dial does not come out without taking the front bracket off. I was trying to say you can hold the shaft with something through the pin hole and push it forward to get the gear...
  14. Replies
    3
    Views
    1,056

    knurling might work. Check the bearing and see...

    knurling might work. Check the bearing and see what you have to work with the shaft dia.

    Good luck !
  15. Replies
    8
    Views
    1,556

    Lathe serial numbers are on top of the tail stock...

    Lathe serial numbers are on top of the tail stock and the bed and the front flat and the V ways.
  16. Replies
    3
    Views
    1,056

    C Mike

    Chrome plate
  17. Replies
    26
    Views
    4,820

    If you might have a number would help. Not so...

    If you might have a number would help. Not so much on Cincinnati laths, Plenty of info on the manual mills.
    Regards,
  18. Replies
    26
    Views
    4,820

    I on't have a lathe. I just trying to help you...

    I on't have a lathe. I just trying to help you with what you have. If you are scraping out your lathe. I just got a call for saddle parts. Hope you are saving them.
  19. Replies
    26
    Views
    4,820

    I will keep the parts in mind.

    I will keep the parts in mind.
  20. Replies
    26
    Views
    4,820

    are you not going to do the bearings. Let me know...

    are you not going to do the bearings. Let me know what the bearing is or the size of the shaft it fits on. I have a couple of bearings that may be the same. They are spindle bearings and on ID has...
  21. Replies
    40
    Views
    4,943

    252127252124Looks like you t a 20 or 24 inch...

    252127252124Looks like you t a 20 or 24 inch circular milling table. manual Pub. no. 2341 Serial no. will be stamped on the top of right clamping flange, like this sample. CUD - 5R. Ask if they have...
  22. I assume you have a manual by the picture you...

    I assume you have a manual by the picture you posted. The little 90 degree cast iron keeper is ground at a 45 degree angle 1/2 inch wide.You will get a bearing with no notch in it. You will have to...
  23. Replies
    3
    Views
    853

    No. 3 Plain M. S. Dial Type Mill Model EA, ER, OM...

    No. 3 Plain M. S. Dial Type Mill Model EA, ER, OM BUILT IN 1943.

    On the left column side by the speed dial.Near the speed change handle, there is a pipe plug. Put a pressure gauge in that spot....
  24. Replies
    43
    Views
    31,315

    Another manual is Pub. M 3540

    Another manual is Pub. M 3540
  25. Replies
    16
    Views
    2,523

    They told the story at the time by the marker on...

    They told the story at the time by the marker on deck where they sigh the surrender. Was how one Japan dive bomber survive the crash on the deck near by. The crew wanted to kill him. The captain said...
Results 1 to 25 of 682
Page 1 of 28 1 2 3 4