Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Cole2534

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    34
    Views
    1,965

    Film temp on a large heating element in direct...

    Film temp on a large heating element in direct contact with the coolant is probably high enough to scorch the coolant little by little over time. You could mitigate this with a liquid/liquid Hx but...
  2. Replies
    19
    Views
    910

    My favorite way to tie-down top-heavy stuff.

    My favorite way to tie-down top-heavy stuff.
  3. Replies
    11
    Views
    989

    Like these? VacuClamp Vacuum Pods | Vacuum...

    Like these? VacuClamp Vacuum Pods | Vacuum Pressing Systems

    If so, I feel like that's a hell of a bargain.
  4. Replies
    51
    Views
    2,987

    [/B] Concur. Hearing a customer's story and...

    [/B]

    Concur. Hearing a customer's story and then being able to say 'I have just the thing for that' is a pretty powerful selling tool.
  5. Easiest way I see to decrease cycle time is a ...

    Easiest way I see to decrease cycle time is a regenerative circuit with relief. Setting the relief pressure will take some fiddling but that shouldn't take but a minute.

    Pardon my ugly drawings....
  6. Replies
    34
    Views
    1,965

    2 thoughts- 1) a cheap sous vide device would...

    2 thoughts-

    1) a cheap sous vide device would be perfect for this. It's got temp/time control, stainless construction and mine is even wi-fi enabled.

    2) I wonder if a UV solution exists to...
  7. Replies
    51
    Views
    2,987

    Bob has said a hundred times and I'm now a full...

    Bob has said a hundred times and I'm now a full fledged believer- an old Fadal is basically a license to print money.

    Sent from my SM-G973U using Tapatalk
  8. Replies
    490
    Views
    30,088

    Funny thing is that lots of other steel shapes...

    Funny thing is that lots of other steel shapes come marked (sheet, pipe/tube and I's/H's come to mind), but I don't recall seeing it on bars.

    Sent from my SM-G973U using Tapatalk
  9. Replies
    490
    Views
    30,088

    Good Q. My supplier provides MTR's for all...

    Good Q.

    My supplier provides MTR's for all materials free upon request. However, I don't have an affirmative way to tie the Ht# on those documents to the bars themselves and even the best 3rd...
  10. Replies
    490
    Views
    30,088

    When he says the same heat I think he means mill...

    When he says the same heat I think he means mill batch, and not heat treat run.

    Sent from my SM-G973U using Tapatalk
  11. Replies
    51
    Views
    2,987

    A Fadal 4020. Sent from my SM-G973U using...

    A Fadal 4020.

    Sent from my SM-G973U using Tapatalk
  12. Replies
    490
    Views
    30,088

    Well, the suggestion was a little tongue in cheek...

    Well, the suggestion was a little tongue in cheek but I do wonder what it'd cost.

    Sent from my SM-G973U using Tapatalk
  13. Replies
    490
    Views
    30,088

    Aermet340 would probably make a nice stud, wonder...

    Aermet340 would probably make a nice stud, wonder what that would cost?

    Sent from my SM-T560NU using Tapatalk
  14. Replies
    47
    Views
    2,560

    I once officed where there was a rail line approx...

    I once officed where there was a rail line approx 50yd from the building and an active army ammunition depot within about 10mi.

    If you were real lucky, the train would go by as the army was...
  15. Replies
    25
    Views
    1,457

    It's supposed be some killer stuff. Sent from...

    It's supposed be some killer stuff.

    Sent from my SM-G973U using Tapatalk
  16. Replies
    25
    Views
    1,457

    1/2" drive shallow, 12-22, 24, 27, 30, 32...

    1/2" drive shallow, 12-22, 24, 27, 30, 32 delivered for $124. That's pretty tempting to try. If nothing else, they can be field tools.
  17. Replies
    17
    Views
    973

    I usually do that, but I'm trying to train myself...

    I usually do that, but I'm trying to train myself to step back from the machine so I can multitask.
  18. Replies
    15
    Views
    953

    What does that metric look like? How would one...

    What does that metric look like? How would one gather it in a medium sized shop, say 10-50 machines? And who determines what is good or not good?
  19. Replies
    7
    Views
    519

    Does it have a blinking light? If so, there's...

    Does it have a blinking light? If so, there's your signal.

    On my Fadal I'd program in a mist coolant op with a short dwell and plug a buzzer into that outlet, but that's because the machine uses...
  20. Replies
    17
    Views
    973

    Reason for my Q was that I need to drill/tap Al...

    Reason for my Q was that I need to drill/tap Al bars in the vise, no critical features or dims. In the manual mill I'd line them up, locate one hole, and then offset by the spacing. In the CNC, the...
  21. Replies
    17
    Views
    973

    Programming multiple parts per fixture

    Hello,
    I suspect this comes down to a mixture of personal preference and resource limitations but I wanted to ask anyway.

    If you're milling multiple identical pieces per fixture, do you program...
  22. Replies
    24
    Views
    2,806

    I saw that on your IG, it turned out very well!

    I saw that on your IG, it turned out very well!
  23. Replies
    11
    Views
    610

    Voltage drop has always been the reason for...

    Voltage drop has always been the reason for chattering contacts in my experience.

    Moonlight, do you have a thermal camera? If so, fire up the salamander and run it for while and look for hot...
  24. Replies
    25
    Views
    1,457

    Wera handtools experiences?

    I have and love my Wera screwdrivers and cruising the net I noticed their basic socket prices seem very fair compared to say Proto.

    Does anyone have experience with thess? Want some 1/2" drive...
  25. Replies
    41
    Views
    2,486

    And you shouldn't. That line of thinking is the...

    And you shouldn't. That line of thinking is the antithesis of this website.
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4