Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: madmachinst

Page 1 of 34 1 2 3 4

Search: Search took 0.01 seconds; generated 12 minute(s) ago.

  1. so what solvent should I use? get teh crud off...

    so what solvent should I use? get teh crud off but yet not get the rubber and other stuff to swell or break.
  2. what is up with the clamp and unclamp prox's. I...

    what is up with the clamp and unclamp prox's. I see the OP doesn't even have them in the outer spindle housing ( hope that is the right name). On mine the prox's are in there but the wire is cut...
  3. so I have a totally different set up, but in this...

    so I have a totally different set up, but in this thread it seems like they are saying that a T32-3 saves all the info in the EEprom and there is a link to a pdf of the start up procedure. T32 wont...
  4. Replies
    18
    Views
    4,256

    Thsi should also work on my SQT 18-ms? In other...

    Thsi should also work on my SQT 18-ms? In other words with the machine sitting in 110F container without power for a while parameters will stay on the EEprom? I aint got no disks. Controller is a...
  5. couldn't afford the T+. I ended up with...

    couldn't afford the T+. I ended up with this.294641

    are the latches in the back just push-buttons. I don't have any visibility there, I can reach it with my hand that is all.
  6. good question, where do I find that without...

    good question, where do I find that without paying Mazak? Copy of parameters I mean.
  7. can I swing those doors open say 15 degrees and...

    can I swing those doors open say 15 degrees and then lift them off their hinges? Remember I only have 11" between shipping container wall and back of machine. So no go on battery tender? I can't...
  8. I'll figure a way. 1st back door from the HS or...

    I'll figure a way. 1st back door from the HS or second door?
  9. SQT 18 MS maintaining parameters while in storage

    Some body told me to add a tender so I don't lose parameters while machine in purgatory. 294355
    Is it one of the back doors I need to open to get to it, cause that seems out of the question.
  10. Replies
    4
    Views
    6,969

    Just got a new machine. had the mechanical...

    Just got a new machine. had the mechanical manual, maintenance manual and some kind of piping/wiring manual. Definitely no programming manual, and it seems no where with the parameters saved in...
  11. so basically you saying with rollback wrecker I...

    so basically you saying with rollback wrecker I need skates and such? Truthfully I want the lathe in between the roll up doorways. I will look for one with a steel bed and most importantly operator...
  12. sorry I meant the white bldg 294128 here is a...

    sorry I meant the white bldg
    294128
    here is a pic of inside. Yeah 175-250 an hr but $780 min charge.

    BTW the machine says it only weighs
    294129
    10,634 lbs
  13. Replies
    13
    Views
    1,299

    want to save money get multiple quotes. I have...

    want to save money get multiple quotes. I have had good experience with a guy called Tom Roedl From Total Quality Logistics.
  14. so here is where it is right now, 294042 and...

    so here is where it is right now,
    294042 and here is where it has to go
    294041 .
    Anybody got a cheaper option than me just calling in the riggers?

    BTW, meanwhile until the machine gets...
  15. well, the bldg is 20X20 I have 2 BP sized...

    well, the bldg is 20X20 I have 2 BP sized machines a light lathe, a few other small machines and then this thing. Can't put in this lathe first and then maneuver the other stuff at least not the...
  16. neighbor seems to have one of those. Keep in...

    neighbor seems to have one of those. Keep in mind, about 50-60 ft of dirt heavily laden with pebbles from container to shop door. Lay sheets of 3/4" plywood on the path and roll it on pipes with...
  17. Now I need suggestions on how to get it out of...

    Now I need suggestions on how to get it out of there and into workshop in the event I can't get a 12000 lb forklift there. I was wondering "wrecker" flat bed? Winch the lathe onto that flatbed...
  18. anywyas here is where teh whole rigamarroo is...

    anywyas here is where teh whole rigamarroo is temporarily landing when it arrives.293675. Will place the 20 ft container on the RR ties besides the wall of the pole barn. Will make for a wonderful...
  19. placing MAZAK SQT 18 MS into shipping container

    Heading says it all. I need to move that machine into a 20 ft shipping container. Got a crane lined up to unload the machine in the container at my property, but the seller says he needs to consult...
  20. so what kind of TIR you think I can realistically...

    so what kind of TIR you think I can realistically expect?
  21. gota a cheap 5c collet chuck and that has to...

    gota a cheap 5c collet chuck and that has to constantly be shimmed in one end. I am beyond certain part sits in there cockeyed.
  22. solid one pc junk. no 2 pc here.

    solid one pc junk. no 2 pc here.
  23. aluminum "collet insert" for 3 jaw that is about .004" TIR

    OK I have this 3 jaw all banged up, too embarrassed to name names. Part I need to flip over and machine on other end to within say .0005" TIR is 5/8" diameter. I was thinking can I get a 2"...
  24. Lady from american Rotary did some math for me...

    Lady from american Rotary did some math for me and said I should be able to run the phase converter and say a few smaller items. Did she do her calculations with the phase converter only running on...
  25. so clearly I need to get a separate disconnect...

    so clearly I need to get a separate disconnect box for the 40 Hp Idler. How many amps you think I need?
Results 1 to 25 of 826
Page 1 of 34 1 2 3 4