Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Peter from Holland

Page 1 of 60 1 2 3 4

Search: Search took 0.08 seconds.

  1. Replies
    38
    Views
    1,860

    Anneal the rivets before use Peter

    Anneal the rivets before use


    Peter
  2. The oldfashion way is to give the motor more mass...

    The oldfashion way is to give the motor more mass
    So bolt a steel disk to the lower flange

    Peter
  3. Well It turns out Schaublin picked the easy way...

    Well It turns out Schaublin picked the easy way out
    They just lett you drill 3 holes in the table
    One for the pivoting pin and 2 for T-bolts

    Peter
  4. In the test report of the milling machine is...

    In the test report of the milling machine is there a tolerance given for the maximum offset ??
    I have never noticed that it was measured in a test report in any milling machine

    Peter
  5. Replies
    12
    Views
    1,051

    What do you mean by saddle lock Here you can...

    What do you mean by saddle lock
    Here you can download a manual and although in french is has plenty of drawings ...
  6. By allignment didnt they mean parralell to the...

    By allignment didnt they mean parralell to the movement of the X ??
    That would be relevant

    Peter
  7. Copyright expires after 70 years after first...

    Copyright expires after 70 years after first publication At least if published by a compagnie
    Otherwise 70 years after the death of the writer
    So it is completly legal to post that information...
  8. Probably at Weiler Another BUT I know that...

    Probably at Weiler

    Another BUT

    I know that on a Matador Weiler changed the theading chart and also the gears needed with a Z=25 gear as the smallest one
    THE REST OF THE MACHINE STAYED THE...
  9. Schould be possible with open delta too Even...

    Schould be possible with open delta too Even single phase is possible

    Peter
  10. Perhaps put a VFD on it and reduce the rpm to...

    Perhaps put a VFD on it and reduce the rpm to the pump accordingly
    Torque stays the same that way Only flow (is speed) is reduced then
    No need for a slow start eighter

    Peter
  11. You can buy standard gears so cheap No need to...

    You can buy standard gears so cheap No need to make them

    Modul on the Condor is 1.5
    HOWEVER
    The Z=21 originaly from Weiler is a special gear as it is bigger as normal That needs to be...
  12. Your ground fault circuit interrupter will trip...

    Your ground fault circuit interrupter will trip inmediatly when you use the ground as neutral
    I sometimes have a machine where the ground is used randomly to generate 220volts single phase
    You...
  13. If it has a controle circuit I would place a...

    If it has a controle circuit I would place a correct sized overload relay in front of the contactor
    If it does not have a controle circuit I would use a motor protection circuit breaker with a...
  14. Neutral needs to be disconnected The neutral...

    Neutral needs to be disconnected
    The neutral is in the powerline to get 220volts single phase (Neutral and one Phase)
    Eighter for the controle circuit or a light or a DRO for example
    In the...
  15. Here I state some valid reassons but nobody is...

    Here I state some valid reassons but nobody is interested in them it seems
    A lott of bitching is preferred

    Peter from Holland
  16. I would buy a dubble colomn saw Kasto HBA360AU ...

    I would buy a dubble colomn saw
    Kasto HBA360AU or a Kasto SSB260VA Behringer also makes great saws
    You could weld 4 bars together at the end and do 4 at a time

    Peter
  17. The machine itself has seen some use The parts...

    The machine itself has seen some use
    The parts look like they have never been used though
    Also all NT 30
    Also the high speed head and even the dividing head
    Never saw a dividing head with NT30...
  18. I was thinking along the same line but why cant...

    I was thinking along the same line but why cant I find it anywhere in the documentation or at a machine
    I did have several of these tables already Never with the bolt
    So thats why I asked here ...
  19. Some more pictures of the accessories and machine...

    Some more pictures of the accessories and machine
    Still need a good cleaning but most of it is never used
    Enjoy
    ...
  20. Aciera F3 auxillary table for setting dividing head at a angle

    FI have bought a nice Aciera F3 NT 30 with a lott of tooling for resale
    Normal table Swivelling tilting table Slotting head Hor arbor High speed head Dividing head
    But also the table for...
  21. The transformer way is to get a single phase ...

    The transformer way is to get a single phase transformer 220 or 110volts input to 460 volts output
    Then a VFD with a single phase input capable of 460 volts and a 3 phase output
    You can change...
  22. That is why you better order from Franz Peter

    That is why you better order from Franz

    Peter
  23. If the Chinese buy ASML they are under a...

    If the Chinese buy ASML they are under a magnifying glass to the government and journalist
    A corrupt official will not do I presume
    Also the government needs to give their fiat for such a...
  24. They still need a permitt to export a machine to...

    They still need a permitt to export a machine to china then

    Peter
  25. It is not the first machine that is sold to China...

    It is not the first machine that is sold to China
    They sell chipmachines for years and years already
    ASML is very well aware that many including some American compagnies are after their secrets
    ...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4