Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: upm2019

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Try metric and multi standard they have a lot of...

    Try metric and multi standard they have a lot of good information plus good inventory
  2. Replies
    5
    Views
    440

    If it is a dryseal (Nptf)then you need full form...

    If it is a dryseal (Nptf)then you need full form insert otherwise a 18 pitch insert should work . Just get the taper right and you’ll be fine
    Pete
  3. I worked for a shop that used these Sanford...

    I worked for a shop that used these Sanford grinders to make all the for tools for their screw machines. First time I saw one I had my doubts but they were pretty impressive
  4. Replies
    13
    Views
    909

    It looks like some one relied too much on their...

    It looks like some one relied too much on their Cad program fo the call out . I believe the NS means near side so it’s gonna be a blind hole . As to the depth refer to machinist hand book .Depending...
  5. Replies
    28
    Views
    1,426

    Very impressive looks better than a gerstner ....

    Very impressive looks better than a gerstner . Also that’s one good thing that came from Covid. Keep up the good work
    Pete
  6. May for sharpening taps or csinks

    May for sharpening taps or csinks
  7. Replies
    5
    Views
    921

    The hole on the end is a center hole also there...

    The hole on the end is a center hole also there is a removable weight
  8. Replies
    5
    Views
    921

    What is this not plumb bob?

    305803305802305801This came in a box of tools I bought a while back . I’ve been puzzling on this for a while thoughts?
    Pete305800 there doesn’t appear to be any markings other then what looks like a...
  9. Replies
    27
    Views
    1,177

    Look at the collet pressure gage if it’s above 20...

    Look at the collet pressure gage if it’s above 20 when the collet is open you will get that alarm. The switch is in the valve compartment it’s a pressure switch . If you look in the manual it tells...
  10. Replies
    14
    Views
    715

    This calculation becomes super crucial for puller...

    This calculation becomes super crucial for puller set ups. If you run too many cycles, the last bit of material will become lodged in the puller then mashed repeatedly into your collet. Could be...
  11. Replies
    7
    Views
    674

    That’s for boring and recessing on a hand screw

    That’s for boring and recessing on a hand screw
  12. Replies
    14
    Views
    715

    I have three Omniturn’s and we use lipe bar feeds...

    I have three Omniturn’s and we use lipe bar feeds . They were 12 feet long but we cut them down to just over six feet to help with the bar whipping and improve finish . We also made an extension for...
  13. The ram is rotated 90 degrees turn it and you...

    The ram is rotated 90 degrees turn it and you should be fine . When I had one the only draw back was if the cutter grabbed it would tip the head up . We had a plug we used .It might be worth the...
  14. They look a bit like Omniturn tool holders Pete

    They look a bit like Omniturn tool holders
    Pete
  15. Replies
    26
    Views
    24,740

    I have had good luck with triumph tools made in...

    I have had good luck with triumph tools made in usa and work good
  16. Replies
    73
    Views
    3,172

    you should look at equipto if I remember you can...

    you should look at equipto if I remember you can get your 12 feet across with posts on the ends. Then a couple along the 32 foot length . Since it’s modular you can configure any way that suits you ....
  17. Replies
    2
    Views
    389

    We put the base outside until we can bust it up...

    We put the base outside until we can bust it up and dump it . Some guy came by and asked if he could have it . I guess he thought it was cast iron I told him he could take it he wanted me to put it...
  18. Replies
    21
    Views
    839

    When I post from my tablet my pics always come...

    When I post from my tablet my pics always come out sideways how do you rotate them
  19. Replies
    7
    Views
    9,926

    I have on I bought at auction 10 years ago . It...

    I have on I bought at auction 10 years ago . It came with a radius attachment which I used once that seemed too cumbersome to learn to use the machine it self is great . You should really use...
  20. I started setting up those things great for its...

    I started setting up those things great for its time . I just saw a few of these at auction a week or two ago they also had the #1 and #2 . They went pretty cheap if you keep your eyes open you can...
  21. Replies
    51
    Views
    10,248

    Before WW2 a lot of Mfg like Brown and Sharpe and...

    Before WW2 a lot of Mfg like Brown and Sharpe and Singer sewing machine made all there fasteners different enough that you couldn’t use off the shelf parts 1/2-12 threads Or odd pitch diameters like...
  22. Replies
    23
    Views
    6,774

    I agree you should call the customer . I was told...

    I agree you should call the customer . I was told when I started out that the only stupid question is the one you didn't ask . Beside's that a call to the customer takes a lot less time then posting...
  23. Replies
    2
    Views
    389

    Parting out Hardinge Conquest 42 SP

    I am parting out a Hardinge Conquest 42 SP with a Fanuc O-T control . I bought the machine at auction and there is a problem with the high res spindle encoder every works with the exception of the C...
  24. Replies
    8
    Views
    1,386

    tag team idiots is what the op and freind are

    tag team idiots is what the op and freind are
  25. Replies
    47
    Views
    2,844

    Sideways photos

    301999
    We have used these chip board boxes they are pretty inexpensive to have made and you can squeeze quite a few on a standard shelf ours are 4x3x12 . Put your parts in and just mark the box #in...
Results 1 to 25 of 68
Page 1 of 3 1 2 3