Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Peter from Holland

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. Before using it I would get those galled places...

    Before using it I would get those galled places smoothend Make sure all somewhat loose particals are removed
    But its a perfect candidate for SKC 63R A slideway compound for repairs, I have used it...
  2. Replies
    42
    Views
    2,331

    Not when it matters That is while cutting Then...

    Not when it matters That is while cutting Then the 2 pieces are still one piece (Does that makes sence:D)But anyhow the gap setting is still the same percentage
    One can check the cutting edge 1/3...
  3. Replies
    9
    Views
    641

    I have the German manual in PDF Send me a PM...

    I have the German manual in PDF
    Send me a PM with your e-mailadres and you get a wetransfer link from me

    Peter
  4. Replies
    27
    Views
    1,963

    Make sure to fill the keyways one way or the...

    Make sure to fill the keyways one way or the other
    The couplings will dig in otherwise
    There are more brands of keyless couplings
    Google for clamping elements or clamping bushes One can put 2...
  5. Replies
    42
    Views
    2,331

    Gap is 5% of sheetthickness So for 10mm sheet the...

    Gap is 5% of sheetthickness So for 10mm sheet the gap is 0.5mm
    Will that cut paper ??
    For 3mm it is 0.15mm
    What gap you need to cut paper??

    Peter
  6. To the OP You said you placed oak boards...

    To the OP
    You said you placed oak boards between the machine and forks
    Oak is a hard wood. I want something to dig in
    A softer wood or better a sheet of rubber
    If you move machines on a...
  7. Gears are too cheap to 3-D print Peter

    Gears are too cheap to 3-D print

    Peter
  8. Replies
    17
    Views
    896

    Thats why I prefer to modify a steady that is on...

    Thats why I prefer to modify a steady that is on the low side for the intended lathe Just mill some flats on the underside and bolt on a subplate
    And if the total wide is about the same as...
  9. Replies
    6
    Views
    518

    Do the jaws originaly belong to the chuck If...

    Do the jaws originaly belong to the chuck
    If replacement jaws were bought at some time these may be a bit stiffer Stone the surfaces with a diamond stone then The trick is to find out which...
  10. Replies
    17
    Views
    896

    Like said before Mill the bottem flat and ad a...

    Like said before Mill the bottem flat and ad a subplate Or better prehaps Mill a groove and bolt a block with a V to it
    Even if the steady ends up a bit high it does not matter to much

    Peter
  11. I have some collets with a extended nose The...

    I have some collets with a extended nose The extension has a radius These are for hobbing
    To grip the workpiece closer to the hob

    Peter
  12. Replies
    9
    Views
    480

    you can bolt 2 of them together and/or mount 2...

    you can bolt 2 of them together and/or mount 2 of them on the same hub to get a thicker gear
    I would make a hub with a flange between the 2 gears and bolt the gears on the flange
    This one is...
  13. Replies
    42
    Views
    2,331

    Oke A shear with a 20mm capacitiy you set the...

    Oke
    A shear with a 20mm capacitiy you set the gap to cut paper the same as one that cuts 0.1mm???:willy_nilly:

    Peter
  14. I vote for a 1ph input 3ph output VFD as well ...

    I vote for a 1ph input 3ph output VFD as well
    The motor fits already ,runs smoother and will not draw that much amps at start-up wen set properly
    If the voltage does not match one can use a 1ph...
  15. I see them with a plain back So you can mount...

    I see them with a plain back
    So you can mount it on a din55022 backplate

    Peter
  16. Replies
    8
    Views
    492

    You send me a request through Werktuigen - koop...

    You send me a request through Werktuigen - koop of verkoop nieuwe en gebruikte machines + gereedschappen | Werktuigen.nl

    Peter
  17. Replies
    42
    Views
    2,331

    Yes Level as a way to get the machine square in...

    Yes Level as a way to get the machine square in all directions
    Check the gap again and make the gap bigger to start with as the gap might have been narrowed and knifes might hit oneanother
    Had a...
  18. The surface it will be looking at needs to be...

    The surface it will be looking at needs to be protected from swarf wear and dust So you end up with a box with a small camara inside So a scale like thing anyhow

    Peter
  19. Replies
    8
    Views
    492

    More to see on his Ebay site You mean this...

    More to see on his Ebay site
    You mean this one?? I do not have one right now
    Alu Deckel ( Riemenschutz) fur Schnellaufkopf Deckel Frasmaschine | eBay

    Peter
  20. Replies
    9
    Views
    480

    Can`t you buy a stock plastic gear Works as well ...

    Can`t you buy a stock plastic gear Works as well

    Peter
  21. Replies
    8
    Views
    492

    You did send me a e-mail already Do you have...

    You did send me a e-mail already
    Do you have the old model high speed head with 16mm collets or the newer one with NT40
    If I know I can see tomorrow if I can help then

    Peter
  22. Replies
    42
    Views
    2,331

    Turn the nut Thats what it is for Peter

    Turn the nut Thats what it is for


    Peter
  23. Replies
    42
    Views
    2,331

    Remove the cover over the motorfan Then...

    Remove the cover over the motorfan Then disengage the brake by pushing the lever that comes out of the cover of the motorfan
    Then turn the motor by the fan


    Peter
  24. Replies
    45
    Views
    4,194

    Well On this one the drive was replaced with a...

    Well On this one the drive was replaced with a different one A2B board was gone Transformers were gone Wiring was a mess
    We dit put it back to original and only after swapping the motor with...
  25. Replies
    45
    Views
    4,194

    If it was gone completly I would have figured it...

    If it was gone completly I would have figured it out quick enough
    But it was loose in a matter that it functioned properly to the eye in manual mode
    Things went wrong in active mode as then the...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4