Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Bluecollarirons

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    1,613

    Got these sourced out. Thanks guys..

    Got these sourced out. Thanks guys..
  2. Replies
    1
    Views
    1,613

    Need some parts made

    Need some small batches of these made and looking to periodically get more ,made down the road. These are probably more suited for one or two man shops with a few CNC mills. Im not looking to get...
  3. Replies
    24
    Views
    2,733

    I got it sorted guys, thanks...

    I got it sorted guys, thanks...
  4. Replies
    24
    Views
    2,733

    Thread goes to end of hole (as far as the bottom...

    Thread goes to end of hole (as far as the bottom tap will allow. Finish is just parted as smooth as you can, a nipple isn't even too much of a trouble. Doesn't have to be like glass. Im gonna face...
  5. Replies
    24
    Views
    2,733

    can you do 200?? timeline I can wait 2 or 3...

    can you do 200??
    timeline I can wait 2 or 3 weeks...
  6. Replies
    24
    Views
    2,733

    Need coil cores made.

    These are easy to make if you have a bar feeder. Its minimal tooling and set up for this job and they are easy to make. All you have to do is keep the bar feeder fed. Having said that I won't pay...
  7. Replies
    26
    Views
    2,928

    roger that,,,

    roger that,,,
  8. Replies
    26
    Views
    2,928

    its not a set tru.. wish it was or else I...

    its not a set tru.. wish it was or else I probably would not be having this problem.. Im gonna call the place i got it tomorrow.. They actually rebuild chucks so they should know how to set it up.
  9. Replies
    26
    Views
    2,928

    oh ok.. I got it.. Its the shoulder where the...

    oh ok.. I got it.. Its the shoulder where the chuck and back plate butt up.. So I face that off a hair?? On just the back plate or chuck body too?? I have a 4 jaw to fit the chuck body
  10. Replies
    26
    Views
    2,928

    Sorry again. But where is the registration...

    Sorry again. But where is the registration shoulder? I have been using a lathe for 7 years but never had to replace a chuck.. So this is new to me..
  11. Replies
    26
    Views
    2,928

    hahahaha,,, Don't worry,, Im not.. Im not the...

    hahahaha,,, Don't worry,, Im not.. Im not the type to haul off and do stuff like that unless its 100% accurate info to do so.. I have learned my lesson with this type of stuff... Btw.. Where on the...
  12. Replies
    26
    Views
    2,928

    the only place on the body i have an...

    the only place on the body i have an uninterrupted edge all the way around is the OD of the back plate. Which is about 7 or 8 thou out as well.. maybe my spindle is not spinning true??
  13. Replies
    26
    Views
    2,928

    sorry,, excuse my lack of experience. whats TIR?

    sorry,, excuse my lack of experience. whats TIR?
  14. Replies
    26
    Views
    2,928

    Its a bison 3 jaw with 2 piece jaws...

    Its a bison 3 jaw with 2 piece jaws...
  15. Replies
    26
    Views
    2,928

    yes it came mounted by bison.. Its a 1-1/2x8 back...

    yes it came mounted by bison.. Its a 1-1/2x8 back plate.. and I'm measuring with a piece of milled round stock and a dial..
  16. Replies
    26
    Views
    2,928

    Bison chuck WAY out

    I have a 1937 SB model C (model A conversion). I just got a 6" 2 piece 3 jaw Bison chuck for it. The chuck is almost 10 thou out of center.. That seems a bit much. Are new chucks supposed to be...
  17. Replies
    5
    Views
    1,570

    9" motor Mount and fly wheel shaking

    So I finally figured out what was making my lathe shake. I took my motor and mounted it on the wall apart from the table to isolate it..Then ran it without the belt tight to the head stock and sure...
  18. Thanks for the reply guys..

    Thanks for the reply guys..
  19. The reason its out like that is because I pulled...

    The reason its out like that is because I pulled it out for the photo..So you can see the spindle.. Thanks though.. And I do have the thrust bearing and fiber on there..
  20. Running lathe with no headstock bearing sleeves??

    First off excuse my ignorance. Im new to this machine.
    So as Im sure some of you have seen I just rebuilt a 1937 SB model C. Im curious if the 1937 model C had bronze bearing sleeves in the head...
  21. 3 phase would be great but way out of my price...

    3 phase would be great but way out of my price range. I think its because the motor is too big. Its is a 1725rpm. The lathe originally came with a 1/4 hp motor so I think 3/4 is overkill. I ordered a...
  22. I thought it was the belt at first too but its...

    I thought it was the belt at first too but its not.. I swapped the belt out and its still doing it.. I also took the rubber mounts off and its still doing it. It was running better with the rubber...
  23. HELP!! South bend 9" motor wheel vibration HELP!!!!!

    I just restored a Model C. Did a gear box conversion on it and its working perfect. Except the who damn thing shakes which is causing chatter. It has a brand new 3/4hp split phase dayton motor on it....
  24. Quick change gear box conversion. (banjo gears needed?)

    Im doing a quick change gear box conversion on a 1937 model C. I know I need a 20 tooth stud gear which I have. Does anyone know what two gears I need on the banjo bracket?

    Thanks guys..
  25. Replies
    10
    Views
    1,944

    You wouldn't happen to know what banjo gears I...

    You wouldn't happen to know what banjo gears I need for the quick change box? I know I need a 20tpi stud gear and I have that..
Results 1 to 25 of 46
Page 1 of 2 1 2