Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Phil in Montana

Page 1 of 43 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    263

    Yes, if you run a nut. and add a 20 amp fuse for...

    Yes, if you run a nut. and add a 20 amp fuse for the 120v plug, if it is ONLY used for the dro you dont need the gfi, but if it used for power tools you need the gfi...Phil
  2. Replies
    17
    Views
    520

    How do you see anything? I once had a big AC with...

    How do you see anything? I once had a big AC with all the masts and cly,s in the way, I put a back up camera in the front and a tv so I could drive it...Phil
  3. Replies
    2
    Views
    182

    Small world I have one also, for about 10 years...

    Small world I have one also, for about 10 years now, could never find a book, a real handy rig.Mine has a seat and you ride and drive like a atv...Phil
  4. It would be fair in Montana, and it cost a lot to...

    It would be fair in Montana, and it cost a lot to have things shipped here...Phil
  5. Replies
    21
    Views
    1,144

    Parts that went in the hbm or the big Bullard,...

    Parts that went in the hbm or the big Bullard, 40,000 lbs...Phil
  6. Replies
    18
    Views
    614

    What I done is machine a new shaft for the motor...

    What I done is machine a new shaft for the motor and build a new end-bell to fit a sterns brake and a bigger bearing, (not for the faint of heart) but is the best fix , a lot of bucks or work...you...
  7. Replies
    3
    Views
    242

    It has been done...but it can be train wreck, I...

    It has been done...but it can be train wreck, I 2nd renting a fork, you add the top heavy of a mill and now put a tilt on it and pull on the base to slide it up a ramp...Gravity will win...
  8. Replies
    18
    Views
    614

    Every dc inj brake I worked on would heat the...

    Every dc inj brake I worked on would heat the motor badly, and everyone would exceed the fla by 3 to 5 times to work, the problem is 2 fold, 1 the impedance of a ac winding is high, where on dc it is...
  9. No with a labor pool we have thanks to our fine...

    No with a labor pool we have thanks to our fine school system, the new help is not worth 8 bucks let alone 15 ( not counting dead money for ss, work comp, ect) so the job will go unfilled...Phil
  10. The problem with a min wage is you are rewording...

    The problem with a min wage is you are rewording a sob that would not learn or improve themselves, with no work ethics or responsibility. The wage has to be a reword on effort and production and...
  11. Replies
    17
    Views
    520

    Hard to say, keep in mind a older forks can be...

    Hard to say, keep in mind a older forks can be gift from god or a nightmare, anything brakes on the fork the repair will be more than the fork is worth, even a leak will cost big bucks. Engine is a...
  12. I have a very large bed mill 36x36x120 50 hp,...

    I have a very large bed mill 36x36x120 50 hp, With the high cost of tooling I still drill first, (its cheap and the mill is nc ) Then finish with a end mill, It may take a little more time but saves...
  13. Replies
    8
    Views
    531

    I have used 50wt engine oil, no problems for 50...

    I have used 50wt engine oil, no problems for 50 years...Phil
  14. Replies
    18
    Views
    614

    You might be better off to go to a pugging style...

    You might be better off to go to a pugging style brake, still needs a f/r starter...It just applies rev 3 phase at a low voltage (50/75 volts) to the coasting motor...Phil
  15. Replies
    15
    Views
    778

    Make dummy thread and see what fits with...

    Make dummy thread and see what fits with blueing...Phil
  16. Just everyday 30 wt...Phil

    Just everyday 30 wt...Phil
  17. Top oil cap is the oil fill... the side is the...

    Top oil cap is the oil fill... the side is the full level,... and the plug on the bottom is the drain...Phil
  18. 2nd the drill, rough mill, and then finish mill,...

    2nd the drill, rough mill, and then finish mill, no speed devil , but it will get there...Phil
  19. Replies
    3
    Views
    235

    You can find other disks on ebay and mod to fit,...

    You can find other disks on ebay and mod to fit, its easy...Phil
  20. Replies
    18
    Views
    614

    I built a few brakes to stop a planner heads...

    I built a few brakes to stop a planner heads (without brakes the heads would coast 20 mins or so )It takes a interlocked starter like a forward rev type or a 2 speed motor contractor, I would build a...
  21. I have made this fit many times for the...

    I have made this fit many times for the paper-mill when they were going here, I would not go more than a .009/.010 fit, At sometime you will need to remove the coupling half...Phil
  22. Replies
    24
    Views
    833

    I tried that one on a 25hp motor the noise was...

    I tried that one on a 25hp motor the noise was outrages ,so I pulled the motor windings out and rewound it to 3 phase (900 rpm special motor)...Phil
  23. Replies
    40
    Views
    2,036

    Have the water jet guys cut the sqr holes, then...

    Have the water jet guys cut the sqr holes, then make a drift to match your taper, heat the plate red/org hot and beat the drift in and out, go to the next hole, grind flat when done...or skip all the...
  24. I could not afford to have a $15 around, I need...

    I could not afford to have a $15 around, I need drug free thinking minds to work with not zombie,s with cell phones waiting for quitting time...Phil
  25. Its great, the boys making 15 will go to to 22.50...

    Its great, the boys making 15 will go to to 22.50 and the head guys will go from 45 to 90 and my shop rate can go from 100 to 250 what not to like???...Phil
Results 1 to 25 of 1062
Page 1 of 43 1 2 3 4