Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: jwearing

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    13
    Views
    496

    Your clearance numbers don't sound right. Is...

    Your clearance numbers don't sound right. Is your indicator mounted on the headstock? Are your headstock clamp bolts tight?
  2. Replies
    5
    Views
    827

    Nice unobtainium Cincinnati tailstock.

    Nice unobtainium Cincinnati tailstock.
  3. Replies
    6
    Views
    688

    Good timing! I need a 16DP 20PA #6. PM on...

    Good timing!

    I need a 16DP 20PA #6.

    PM on its way.
  4. Dude, you’re killing me. $1500!? For a working...

    Dude, you’re killing me. $1500!? For a working t&g? That’s a great deal.
  5. 50-Taper Chuck Back Plate / Arbor For Cincinnati Dividing Head

    This will fit a Cincinnati 10" dividing head with a 50-taper spindle. It's missing the nut. Also it has some dings that will need to be stoned out.

    4.7" diameter, 9-3/4" total length, 7-3/4"...
  6. Replies
    81
    Views
    11,706

    New favorite air tool: needle scaler. 269834 ...

    New favorite air tool: needle scaler.

    269834

    Also, the motor came out great.

    269832
  7. Replies
    81
    Views
    11,706

    Done. Worked great. 268871 I knurled it,...

    Done. Worked great.

    268871

    I knurled it, then burnished it a bit by pressing the old bearing on and off a few times. Now it fits perfectly.

    Not ideal, but I bet it lasts 20 years or so...
  8. Replies
    81
    Views
    11,706

    What do you guys think about knurling it, or...

    What do you guys think about knurling it, or tapping all around with a center punch to raise some material up to the original diameter?

    I only have to raise the surface .002" (.004 is on the...
  9. Replies
    81
    Views
    11,706

    Getting everything reassembled and I notice some...

    Getting everything reassembled and I notice some damage on the clutch shaft from a spun bearing. There is about .004" wear on the diameter, not terrible but enough that the bearing is loose.

    I'm...
  10. Replies
    81
    Views
    11,706

    The discs varied in condition. Some are...

    The discs varied in condition. Some are delaminating. One blistered (my fault, used heat degreasing, oops). The one pictured here was not my fault.

    The 6 in the previous photo were the best of...
  11. Replies
    81
    Views
    11,706

    The twin disc clutch is another impressive piece...

    The twin disc clutch is another impressive piece of engineering. The only problem is that it was discontinued 60 years ago, and they don't exactly stock the friction discs at Autozone.

    268121
  12. Replies
    8
    Views
    769

    I do believe it. There is a huge difference...

    I do believe it. There is a huge difference between these two companies: Apple sells electronics, Google sells advertisements.
  13. Replies
    8
    Views
    769

    Google maps is a free service that has nothing to...

    Google maps is a free service that has nothing to do with your cell provider. They make money by tracking you, learning about you, and advertising. You can get an iphone and use Apple maps instead,...
  14. Replies
    81
    Views
    11,706

    Where do they normally stamp the timing marks? I...

    Where do they normally stamp the timing marks? I was aware that they would be matched but I couldn’t find any marks. I made sure to preserve the original alignment when I reassembled them.

    Thanks...
  15. Replies
    81
    Views
    11,706

    PIV is done. New bearings, seals, and chain. ...

    PIV is done. New bearings, seals, and chain. Also one of the arms on the tension screw was broken so I had to fab a new one (didn't get any photos). I guess someone tried to adjust it when it...
  16. Replies
    6
    Views
    1,300

    Thanks again! If anyone is interested, this is...

    Thanks again!

    If anyone is interested, this is lathe #36734, already discussed here:...
  17. Replies
    15
    Views
    2,339

    So where does the rust go? I thought the whole...

    So where does the rust go?

    I thought the whole point was to transfer the rust from cathode to anode.
  18. Replies
    81
    Views
    11,706

    I started work on the PIV. Interesting that it...

    I started work on the PIV. Interesting that it is dated 1960, the machine is a 1939. I guess the PIV had been replaced.

    264605
    264606

    So, I guess this is what a worn-out PIV chain looks...
  19. Replies
    6
    Views
    1,300

    Yes, please! Don't scrap anything, PM on the way.

    Yes, please! Don't scrap anything, PM on the way.
  20. Replies
    81
    Views
    11,706

    The speed control cleaned up nicely. I love the...

    The speed control cleaned up nicely. I love the cast bronze conical speed dial. The others I have seen in photos are flat.

    There are no lube points on this, and no mention of it on the lube...
  21. Looks good, maybe I should do something similar....

    Looks good, maybe I should do something similar.

    How much does this increase the humidity of your workspace? Enough to worry about causing rust?
  22. Replies
    81
    Views
    11,706

    On my lathe, the flex shaft that connects the...

    On my lathe, the flex shaft that connects the speed control to the PIV is just a wire rope. Surely this is not original, right? Do any of you guys with PIV models mind taking a look and letting me...
  23. I received the high number plates today. ...

    I received the high number plates today. Excellent! Thank you. Great packing too.
  24. Replies
    81
    Views
    11,706

    Do you other Hendey owners have an opinion about...

    Do you other Hendey owners have an opinion about running the spindle in reverse?

    I understand that it is not really necessary on a lathe with leadscrew-reverse. But it still must come in handy...
  25. I will take the high number plates. PM coming.

    I will take the high number plates.

    PM coming.
Results 1 to 25 of 96
Page 1 of 4 1 2 3 4