Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: moonlight machine

Page 1 of 60 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    21
    Views
    684

    Once again, Call Curtis, he is a wealth of...

    Once again, Call Curtis, he is a wealth of knowledge. He will get you the correct insert, but just as important he can also tell you the correct speed, feed and depth of cut.
  2. Replies
    26
    Views
    999

    I was working in Fort Lauderdale about 30 years...

    I was working in Fort Lauderdale about 30 years ago. Weld shop a few blocks away is cutting up a tank truck for scrap. It blows up and kills a few of them. They take a few days to plant the dead and...
  3. What??????

    What??????
  4. You need to feed it faster so it breaks a chip....

    You need to feed it faster so it breaks a chip. Those long curls can be dangerous. Proper feed, speed and depth of cut will break the chip and give you a finish.
  5. Replies
    9
    Views
    1,888

    Look closely at the thread chart between the bull...

    Look closely at the thread chart between the bull gear and the chuck,

    ...
  6. 160.00 freight......what a rip!!!!

    160.00 freight......what a rip!!!!
  7. Replies
    7
    Views
    784

    Anyone hear from wrustle?

    I miss his posts, is he still with us? The recent thread about Adama makes me hope for the best.
  8. I have one around here somewhere, I took it off...

    I have one around here somewhere, I took it off because all it did was collect chips. My collets are in a rack I made in a drawer.
  9. Replies
    25
    Views
    1,521

    More like very annoying.

    More like very annoying.
  10. The pin assembles through a slot. My proposal...

    The pin assembles through a slot. My proposal will be to open the slot .010. Change to a roll pin from the dowel. leave the hole in the shaft as it is other than open the top so the pin hits all...
  11. I mill them with a 1/8" end mill. No way to ream...

    I mill them with a 1/8" end mill. No way to ream them without a guide, made one of those as well.
  12. A step hole and a shaft locking tool will be part...

    A step hole and a shaft locking tool will be part of my repair proposal.
  13. Replies
    1,147
    Views
    91,580

    1693 They did not burn them. They did hang 21...

    1693 They did not burn them. They did hang 21 though.
  14. Replies
    21
    Views
    1,277

    Sooooo w t f is an ID red head?

    Sooooo w t f is an ID red head?
  15. Replies
    82
    Views
    5,752

    As you repeat ad nauseum. I for one am tired of...

    As you repeat ad nauseum. I for one am tired of your endless harping about our health care system. It does not affect you in any way shape or form so SHUT THE FU*K UP!!!
  16. If you are using the quill you will find that...

    If you are using the quill you will find that .003 tilt moves the cutter a fair ways between quill up and down. I have a 7" diameter tapered roller bearing race that I lay on the table as a track for...
  17. I have worked with the assembly guy on fits and...

    I have worked with the assembly guy on fits and tolerance issues in the past by request of the owner. I don't know the dowel pins are all the correct size but it is time to sort it out.
  18. The blind hole in the shaft is not totally blind,...

    The blind hole in the shaft is not totally blind, it is .188 dia to .430 depth then thru at .125 dia. There is a hole through the part the shaft goes through. To remove the pin in the original design...
  19. It is a hard dowel pin.

    It is a hard dowel pin.
  20. I am modifying an existing part that is expensive...

    I am modifying an existing part that is expensive so if I can somehow upset ihe ID and then finish the diameter they can be saved.
  21. The shaft goes thru a part with a .190 slot that...

    The shaft goes thru a part with a .190 slot that the pin goes thru. the slot limits the rotation as well as setting the location of the shaft. A 2 diameter pin will not work.
  22. It is not a thru hole and it is .230 off center...

    It is not a thru hole and it is .230 off center on a .708 dia round bar. Not the end, the top of the hole goes around the bar.
  23. Is it possible to reduce a .192 dia. hole to be a proper fit for a .187 dowel pin?

    A long story. .708 diameter steel shaft. The drawing calls out a .188 diameter hole, .430 deep .230 off center. All well and good. I do 25 and get about 6 back, the hole is too small but my size pin...
  24. If you want a CNC lathe just buy one. If you are...

    If you want a CNC lathe just buy one. If you are bound and determined to build your own at least start with decent iron. That atlas is a total POS, leave it at the curb and get a lathe not a lathe...
  25. Is that the original motor? I have never seen a...

    Is that the original motor? I have never seen a 3hp on a 15 Regal. Normally 5 or 7.5hp. The electric brake is behind the big pulley driven by the motor. If you think the brake is dragging just unplug...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4