Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: ifixcnc

Page 1 of 19 1 2 3 4

Search: Search took 0.01 seconds.

  1. 100 ppm U-L listed detectors must sound a full...

    100 ppm
    U-L listed detectors must sound a full alarm within 90 minutes or less. Most alarm more quickly. Time to alarm varies with manufacturer, with some manufacturers electing to sound the alarm...
  2. Replies
    9
    Views
    733

    Sounds like the MC relay is not pulling in. Do...

    Sounds like the MC relay is not pulling in.
    Do you have electrical prints for it?
  3. Replies
    11
    Views
    796

    Some machines have an M code to enable the 900,s...

    Some machines have an M code to enable the 900,s
    M999 and M998 are common.
  4. Thread: Parameter Help

    by ifixcnc
    Replies
    1
    Views
    334

    Our T2 is funny when the battery's are low. ...

    Our T2 is funny when the battery's are low.
    Sometimes just leaving it on for several hours will build up enough charge that it will load.
    There are multiple battery's.
  5. Replies
    7
    Views
    504

    I save a copy to open, so if the file gets...

    I save a copy to open, so if the file gets changed or corrupted the original is in tact.
  6. They have an warehouse in my backyard, and will...

    They have an warehouse in my backyard, and will not give an catalog to anyone who sells anything that they sell. They view it as feeding their competitors?
  7. Replies
    5
    Views
    376

    Far left key is op/maint 1ST F5 is info ...

    Far left key is op/maint 1ST
    F5 is info 2ND
    F3 is Maint M codes = MMCodes 3RD

    Far Right is return if you get off course.
  8. Replies
    5
    Views
    376

    One of the softkeys will take you to another set...

    One of the softkeys will take you to another set of screens. The Mcodes are there.
  9. Replies
    5
    Views
    376

    You need to recover with the maintenance M codes....

    You need to recover with the maintenance M codes. M998 & M999 enable and disable the M9__ # codes.
    Do you have the version with an second screen? if so there is a page there that lists the M codes.
  10. Being that Hermle USA is in Wisconsin it is no...

    Being that Hermle USA is in Wisconsin it is no surprise that you had good service.
    I worked for an dealer that sold Hermle for a while, and I can tell you that they are crazy complicated.
    A good...
  11. https://www.newark.com/tadiran-batteries/tl-5903-p...

    https://www.newark.com/tadiran-batteries/tl-5903-p/battery-lithium-3-6v-aa/dp/96B6172?st=3.6%20volt%20lithium
  12. I think it is an A size, 3.6 Volt, Lithium. ...

    I think it is an A size, 3.6 Volt, Lithium.
    Fairly common cell, you would just have to transplant the wire and connector.
  13. Not knowing your time frame or quantity, I cant...

    Not knowing your time frame or quantity, I cant say if this is a reasonable alternative.
    Looks to me like fair quality, and low price for unfinished machinery.
    http://www.zzsmartech.com/
  14. Replies
    9
    Views
    675

    When it is at the point that some characters are...

    When it is at the point that some characters are visible, change modes and see if the screen changes.
  15. Yes it is specific to the MTB. If you can find...

    Yes it is specific to the MTB.
    If you can find the wires from the switch at the I/O board, open the circuit (pull the wire) and close it (jump the wire)
    If your bit changes then check the wires.
  16. That page is the Y bits = Outputs, that turn on...

    That page is the Y bits = Outputs, that turn on the indicator light.
  17. The X bit is a builder determined thing. What...

    The X bit is a builder determined thing.
    What control and machine is this?
  18. Try Industrial Monitors, Flat Panel LCD...

    Try

    Industrial Monitors, Flat Panel LCD Display, Touch Screen & CRTs
  19. When I worked for an Doosan dealer we would...

    When I worked for an Doosan dealer we would install battery holders, so you could just pop in a new cell. Serviced lots of servo turrets and never noticed a pattern to the timing of the cells going...
  20. The 18 has diagnostic pages, not parameters....

    The 18 has diagnostic pages, not parameters. System key, the left soft key is Param, the one to the right of it is diag. Hit that soft key and page down to 201. It is an 8 bit word, and which ever...
  21. The problem I have found, is that a lot of the...

    The problem I have found, is that a lot of the "new" 3.6v batteries have been on the shelf for an long time, so they are not fresh. Buy them from an place that sells a lot of them and the odds are...
  22. I am all for it, as I got robbed by member Fancy...

    I am all for it, as I got robbed by member Fancy Jigs, on an Ballscrew.

    2CW
  23. Replies
    511
    Views
    43,070

    Schnit does happen.269628

    Schnit does happen.269628
  24. Replies
    11
    Views
    1,193

    Try MC Machine 9000 Brookpark Rd,...

    Try

    MC Machine

    9000 Brookpark Rd, Cleveland, OH 44129

    (216) 398-3666

    It has been a couple of years since I have dealt with them, but they are into BIG parts.
  25. Replies
    24
    Views
    1,871

    I don't know about OKK but, our Mitsui Seiki's...

    I don't know about OKK but, our Mitsui Seiki's want T0 at the end of the program, to clear tool memory. That way the next program start has an empty spindle to start with.
Results 1 to 25 of 473
Page 1 of 19 1 2 3 4