Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: TeachMePlease

Page 1 of 60 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    8
    Views
    293

    I mean, his other posts seem legit. Maybe just...

    I mean, his other posts seem legit. Maybe just coinky-dink?
  2. Thread: reamer ?

    by TeachMePlease
    Replies
    7
    Views
    584

    If the hole is only .080" deep, as your post...

    If the hole is only .080" deep, as your post states, you're not even getting past the lead chamfer on the reamer, so you're not cutting to size.
  3. Replies
    19
    Views
    1,155

    Poor recruiter had no idea what he was getting...

    Poor recruiter had no idea what he was getting into... :nutter:
  4. This is why we :drink: :D It's not vital to...

    This is why we :drink: :D


    It's not vital to our work... Just something that would have helped to know.

    The day goes on.

    We get hot dogs for lunch today, so there's that.
  5. Well, I talked with him after this post, turns...

    Well, I talked with him after this post, turns out, he hadn't sent me on a total wild goose chase. There was a sample part in the same box as the drivers, but he had it with him, so when I looked in...
  6. Replies
    79
    Views
    4,046

    Serious question, how would that work, liability...

    Serious question, how would that work, liability wise?

    Employee is not on the clock, but in a company vehicle, and rear ends grandma at a stoplight... Whose insurance pays for her busted pelvis?...
  7. Replies
    9
    Views
    945

    So on my newer Mits controls, there is a setting...

    So on my newer Mits controls, there is a setting that, when checked, will not allow the feedrate to exceed 100%, regardless of the position of the feedrate override dial. No idea if such a thing...
  8. Replies
    79
    Views
    4,046

    Use your Chevrolegs!

    Use your Chevrolegs!
  9. So I'm in that "small Swiss world"... I can't...

    So I'm in that "small Swiss world"... I can't think of a time I've needed, or even seen a sleeve like that. But if you tell me what manufacturer you saw something vaguely resembling what you need, I...
  10. Well, in today's "I'm gonna smack my coworker"...

    Well, in today's "I'm gonna smack my coworker" moment...

    I went to get a sample of WHATEVER this is, so I could have it XRF'd again...

    It's a freaking bit driver he ordered from McMaster.

    I...
  11. I was just handed these numbers and told to...

    I was just handed these numbers and told to figure it out.

    I'll send another sample to the XRF and see what I get back. I know nothing else about this. I don't even know WHY they want to know......
  12. For whatever reason, those are what the gun is...

    For whatever reason, those are what the gun is preprogrammed for. Presumably because with those numbers we can tell 303 from 304 from 316 from 17-4 from 17-7 etc.

    Presumably. I know even less...
  13. Help Identify Steel: 7.75%Cr 18.32Fe .04%V .91%Ni

    As the title says...

    My metallurgy is not that awesome, I generally read up on things when I need to know them, or ask here. I was just handed a printout from an XRF gun and asked to identify the...
  14. I've always been told that it's to prevent...

    I've always been told that it's to prevent erosion of our foundations. Given the sandy soil here, it's not uncommon to see a trench in the dirt/grass around a house with no gutters where the rainfall...
  15. What size shanks do you need?

    What size shanks do you need?
  16. Nope. It's an aquifer.

    Nope. It's an aquifer.
  17. When they built my house I noticed I didn't have...

    When they built my house I noticed I didn't have gutters on the front, even though the identical house (owned by my friend, which is why I bought mine), built 6 months prior DID have gutters. I made...
  18. Replies
    19
    Views
    1,155

    I was thinking that the obvious "on sight" vs...

    I was thinking that the obvious "on sight" vs "onsite" was pretty glaring, too.
  19. Replies
    55
    Views
    38,927

    Where are you currently sourcing your material?...

    Where are you currently sourcing your material? They can't give you any advice?

    I mean, Fastenal lists it: 5/16" x 12' 17-4 H-1150 Stainless Steel Round Bar
    | Fastenal

    These guys list it:...
  20. It was recently decided that this community,...

    It was recently decided that this community, about 15 mins from my house has the most lightning strikes of any place in Florida:
    New lightning capital of the U.S. now in SWFL

    I built my house 2...
  21. Replies
    70
    Views
    9,353

    I've no idea what a license costs, but the...

    I've no idea what a license costs, but the software BeyondCompare lets you choose two files (in your case, the program on the USB and the program on the PC) and do a quick compare. It will put the...
  22. Well, I'm a young guy, and the word is "irks"....

    Well, I'm a young guy, and the word is "irks". "Erks" is what you have left after you drop a part and break off one of your zerks...
  23. Are you trying to describe a 1" square pocket...

    Are you trying to describe a 1" square pocket with a .250" square island at its center?
  24. Replies
    55
    Views
    38,927

    Possibly way out there question, possibly save...

    Possibly way out there question, possibly save you a lot of time, effort, and energy question... Do you NEED it to be H1150?

    Are you looking for the increase in yield strength, with the trade off...
  25. Replies
    16
    Views
    923

    Pretty sure using a floating holder is...

    Pretty sure using a floating holder is contraindicated for rigid tapping. At least, on a machine that's in good shape.
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4