Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: upcondor

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Please remove listing

    Please remove listing
  2. Please remove listing

    Please remove listing
  3. FS: South Bend Model 9A Telescoping Follower Rest

    I have the above follower Rest in very good condition for sale.
    Has the original bolts with it. In the pics they are wrapped with tape to keep them with the rest.267012267013

    Price is $ 225.00 +...
  4. FS: Jacobs 59B Headstock Chuck, 1.5 x 8 tpi

    267011267010267009The above 1.5”x 8 tpi headstock chuck is in very clean condition . It has a range of 3/16” to 3/4”. It comes with the original chuck key.

    Price is $ 85.00 + shipping.
  5. More good info from experienced people, thank...

    More good info from experienced people, thank you.

    Tom
  6. Replies
    3
    Views
    730

    Good deal. Will double check the detents go into...

    Good deal. Will double check the detents go into place and also check cam turn/ position..
  7. Ok thanks for info. Can the fuse be the same type...

    Ok thanks for info. Can the fuse be the same type used in an auto of the correct size ?
  8. Well ended up communicating with some YouTube...

    Well ended up communicating with some YouTube machinist and decided to go with a Lenze VFD. Brad Jacobs and Bar Z “Stan” both have very good videos on installation. Also upgraded to 10 gauge for...
  9. Replies
    3
    Views
    730

    South Bend Heavy 10L D-1 4 Spindle

    I am doing a tear down cleanup of my newly acquired circa 1981 South Bend Heavy 10L which has a D1-4 spindle.

    I backed out the locking cams and found the 3 detents badly damaged/ springs in...
  10. Yessir, dedicated outlet. Thank you for the info....

    Yessir, dedicated outlet. Thank you for the info.
    Was hoping it was not going to be larger than 10 ga. which I had in stock.
    12 ga sounds good.

    Lucked out finding the lathe and looking forward...
  11. South Bend Heavy 10L wire gauge size for power

    Recently acquired a 1981 SB Heavy 10L, serial number 22022R. It has a Dayton 1 HP 3 ph motor on it. I am having to run power about 40’. The lathe will be operated with a VFD.

    Can anyone help with...
  12. Did not find any numbers at all. Tom

    Did not find any numbers at all.

    Tom
  13. Ok, will try this evening.

    Ok, will try this evening.
  14. Thanks for the additional info and pic for...

    Thanks for the additional info and pic for reference. I was unable to find any code at all on the bed as swells referred to.
  15. Ok I will thanks

    Ok I will thanks
  16. Ok, pretty sure from the wear on the v ways this...

    Ok, pretty sure from the wear on the v ways this one is not hardened. But I have limited experience with SB as you can see.
  17. The comments I refer to were made by an...

    The comments I refer to were made by an individual near me that has the lathe for sale. The seller gave me information on the lathe that I felt was incorrect. I deferred to this site for your help/...
  18. Thank you very much for your help ! Will put to...

    Thank you very much for your help ! Will put to rest comments made about a lathe for sale. It is the “X” braced bed.

    Tom
  19. Replies
    11
    Views
    1,128

    Serial number 7693TKL, looks to be a 1959 version...

    Serial number 7693TKL, looks to be a 1959 version with taper attachment. Born date seen on your serial number page and thank you for maintaining it.

    Tom
  20. Replies
    11
    Views
    1,128

    Hardened beds on South Bend lathes

    What year did South Bend begin using harden beds on their 13” lathes that have the large spindle hole ?

    Thanks for any help,

    Tom
  21. Thank you for the help. I was looking at the...

    Thank you for the help. I was looking at the serial number page wrong but see it now. The lathe v-ways show some wear in the normal area (12-14”) from headstock. With a 1959 born date I thought this...
  22. South Bend 13” manufacture date/ need help

    I have a South Bend 13” lathe that I am trying to find out the manufacture date of. The serial number is 7693TKL14.

    I know the following T=13”, K= QCG, UMD, and Friction Feed,
    L= Large Spindle...
  23. Replies
    8
    Views
    599

    Ok, after taking some good measurements looks...

    Ok, after taking some good measurements looks like it is the area before the thread. Going to have to be bored out 2 thou.

    Thanks for helping out,

    Tom
  24. Replies
    8
    Views
    599

    Ok will do ! Tom

    Ok will do !

    Tom
  25. Replies
    8
    Views
    599

    More good info, appreciate the help... Thanks...

    More good info, appreciate the help...

    Thanks

    Tom
Results 1 to 25 of 50
Page 1 of 2 1 2