Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: jancollc

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds; generated 6 minute(s) ago.

  1. Replies
    15
    Views
    499

    What is the material that you have to run so slow?

    What is the material that you have to run so slow?
  2. Replies
    5
    Views
    391

    Even if your parts are so large that a used...

    Even if your parts are so large that a used tumbler was 6K, it would still pay for itself in short order compared to blasting them one at a time...

    You can find C&M 3FT^3 tumblers for a lot less...
  3. Replies
    262
    Views
    31,029

    The planners here have created an "Urban Growth...

    The planners here have created an "Urban Growth Boundary". Beyond which, the zoning prohibits most commercial activities. To prevent "urban sprawl" as they say. I think it's to keep the "farms and...
  4. Replies
    24
    Views
    1,014

    On my VMC's I always use IPM. On the lathe, it's...

    On my VMC's I always use IPM. On the lathe, it's IPR.

    Either one is fine, you just better know which one you are using...

    @OP- get your speeds and feeds better- for 250rpm you should feed at...
  5. Looks to me like the latter. With the exception...

    Looks to me like the latter. With the exception maybe of some 3D printing stuff.

    The list of exhibitors has no major MTB's that I can see. Lots of process stuff, not much in the way of machine...
  6. Replies
    11
    Views
    844

    Have you tried Crest? Marine Toe Rail &...

    Have you tried Crest?

    Marine Toe Rail & T-Track | Crest Aluminum Products Co, Inc
  7. Replies
    6
    Views
    545

    You can't just stuff a 10mm tap in an 8mm hole....

    You can't just stuff a 10mm tap in an 8mm hole. You have to drill first.

    You shouldn't do that anyway- you should helicoil it back to the original thread.
  8. Replies
    61
    Views
    7,164

    The certification they falsified was a process...

    The certification they falsified was a process (part of the heat treat} specification. It was not something that is going to show up in a lab test. The lab will tell you what you have, but it cannot...
  9. Replies
    11
    Views
    844

    What kind of profiles are you looking for? ...

    What kind of profiles are you looking for?

    Misumi stocks a bunch of standard profiles for doing frames and motion control type stuff.

    If you're looking for boat specific shapes like toerails...
  10. Replies
    5
    Views
    436

    Just practice. Bring your indicator down to just...

    Just practice. Bring your indicator down to just above the part, and sweep it around. Make your big adjustments. Then bring it down, do X first. Zero the dial on the first side, rotate 180 degrees...
  11. Replies
    7
    Views
    839

    If the leak is at the large bottle- either the...

    If the leak is at the large bottle- either the shutoff valve or the connection to the check valve, the small bottle would not see the pressure drop in the large bottle.
  12. Replies
    48
    Views
    25,187

    I assumed you had a floating holder by your...

    I assumed you had a floating holder by your feedrates. Yes, you can change the RPM in the program.

    The tension/extension holders vary. Some release, some don't. Releasing holders are designed that...
  13. Replies
    16
    Views
    1,084

    24 CFM will obviously be enough for a mini mill....

    24 CFM will obviously be enough for a mini mill.

    As to the rest- Dewalt, Porter Cable, Kobalt, Craftsman, etc are all cheap consumer grade compressors. Right at home in any garage.

    They will...
  14. ebay ad here: Faro 9ft EDGE Arm CMM w/ Laser...

    ebay ad here:

    Faro 9ft EDGE Arm CMM w/ Laser Scanner HD LLP 2015 V6 HARD CASE 3.9REV | eBay

    Seller does have 100% positive feedback on a large number of transactions, looks legit.
  15. Replies
    48
    Views
    25,187

    Well, you might start by putting F.050 in your...

    Well, you might start by putting F.050 in your G95 lines so your feedrate matches the tap's pitch.

    General practice to start the tapping cycle farther then .020" from the part, so your spindle has...
  16. Replies
    49
    Views
    2,054

    A new Gerstner would put any machinist "over the...

    A new Gerstner would put any machinist "over the moon". But one Gerstner would buy 5 Kennedy's, so there is that...

    We use our top boxes for measuring tools, which is why they have felt lined...
  17. CosmosK. I would be happy to be a CAT40...

    CosmosK. I would be happy to be a CAT40 volunteer. Also have BT40 and it would be great if it fits both.
  18. Replies
    11
    Views
    601

    My first look I thought is was an ONG keypad. I...

    My first look I thought is was an ONG keypad. I can make out the softkeys below the display.

    I zoomed the pic and see it's not a Fanuc ONG though, not sure what it is. Maybe an old Anilam or...
  19. Replies
    11
    Views
    601

    That's an old Fanuc 6M? I don't know what the...

    That's an old Fanuc 6M? I don't know what the other monitor is for.

    Assuming the control works, normal G code programming...

    edit: closer look, appears to have softkeys, so may be 10 or 11M.
    ...
  20. Replies
    5
    Views
    356

    I just hang them on a pegboard behind the machine.

    I just hang them on a pegboard behind the machine.
  21. Replies
    8
    Views
    864

    You should be asking your accountant these...

    You should be asking your accountant these questions.

    You will need to setup your insurances. Workman's comp, Unemployment, Commercial General Liability to start.
    You will need a Federal EIN for...
  22. Replies
    8
    Views
    7,352

    I have a copy of an old Anilam pdf that seems to...

    I have a copy of an old Anilam pdf that seems to be kind of a generic "Wizard" series manual. It has configuration and operations for mini,micro, and Wizard series.

    PM email addy if anyone wants...
  23. Dan, the link I posted for NTPI- they do...

    Dan, the link I posted for NTPI- they do trav-a-dials.

    The reason I decided not to rebuild it was that the cost tbey quoted over the phone was about 1/2 what I would pay for a cheaper DRO setup...
  24. Replies
    50
    Views
    2,329

    I don't have any problems with water in my...

    I don't have any problems with water in my downstream receivers, I have one upstairs and one down on the shop floor.

    I put shutoff valves on every receiver so I can isolate the sections. Each...
  25. I haven't used them, but I've talked to them on...

    I haven't used them, but I've talked to them on the phone and they seemed like they had their act together. I was looking for a trav-a-dial rebuild.

    NTPI - Repair Services
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4