Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: TeachMePlease

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Check with Keyence? They were just here demoing...

    Check with Keyence? They were just here demoing all their safety stuff. Granted, everything they showed us was door interlocks, light curtains, etc, but maybe they have something that fits the bill?
  2. I haven't used it, but I had a rep show me this...

    I haven't used it, but I had a rep show me this recently, maybe it can help you? Looks to be a step above standard loc line.

    Cooling Line
  3. Second one says "Yeah, and the bottom's muddy!"

    Second one says "Yeah, and the bottom's muddy!"
  4. Replies
    5
    Views
    344

    You can get a brand new Acer for $9k.... Just...

    You can get a brand new Acer for $9k....

    Just saying...
  5. Replies
    512
    Views
    33,935

    It's not the fault of the car that the driver is...

    It's not the fault of the car that the driver is using it irresponsibly.

    It is explicitly stated that the car is not Fully Self Driving, and that the driver is responsible for maintaining an...
  6. Replies
    20
    Views
    1,152

    Swiss lathes do it like this, Tom: M3S1=3500...

    Swiss lathes do it like this, Tom:

    M3S1=3500
    G98 G0 Z-.01 X.3149
    G1 Z5.118 F.002
    X.43307
    Z5.9055
    U.05W.05

    Slightly less than a minute per part (depending on material, could be faster,...
  7. Replies
    512
    Views
    33,935

    2 Teslas "recently"... Even if there were 2 in...

    2 Teslas "recently"... Even if there were 2 in the same day...

    Number of car crashes in the US per day: 17,250
    Number of fatal car crashes in the US per day: 102
    (Both numbers from NHTSA...
  8. Replies
    512
    Views
    33,935

    I was taught that arguing with an idiot (not...

    I was taught that arguing with an idiot (not calling anyone here an idiot) is like teaching a pigeon to play chess... No matter what happens, the bird will crap all over the board and strut around...
  9. Replies
    49
    Views
    3,143

    Is that a dig at Ox the moderator? :D Our...

    Is that a dig at Ox the moderator? :D

    Our wrestling coach used to tell us that a good wrestler was strong like bull, smart like tractor.

    That hand looks awful
  10. Replies
    49
    Views
    3,143

    Times I've almost knocked myself out, a two act...

    Times I've almost knocked myself out, a two act play, written by me:


    First time, I was demoing an old skateboard ramp (I used to be a carpenter). I had a bunch of 8ft long 2x4's that had been...
  11. Replies
    49
    Views
    3,143

    So if he's coming out the presumably open...

    So if he's coming out the presumably open passenger side door... Does he get thrown down by his own car?
  12. She doesn't know where all the bodies are. ...

    She doesn't know where all the bodies are.

    (And I pay all the bills :D)
  13. Replies
    512
    Views
    33,935

    How do you feel about the "war on drugs"... Or...

    How do you feel about the "war on drugs"... Or the "war" in the middle east? Or the fact that you're paying for food stamps for wal mart employees so they don't have to pay their employees more?
    ...
  14. I keep a list, with usernames and passwords, and...

    I keep a list, with usernames and passwords, and my girlfriend knows where it is.
  15. I read it as finishing from 7.5mm to 8.0mm final...

    I read it as finishing from 7.5mm to 8.0mm final depth.
  16. Maybe I'm crazy... But couldn't you build a ramp...

    Maybe I'm crazy... But couldn't you build a ramp for parts to slide down, instead of drop?
  17. Hmm... 2 vices... If the depth of that slot in...

    Hmm... 2 vices... If the depth of that slot in your image is 7.5mm, extrapolating, your plate is about 25mm thick... How long/wide is this plate that needs to be held in two vices? Is this slot...
  18. Replies
    19
    Views
    1,244

    Flatness simply describes two planes between...

    Flatness simply describes two planes between which the entire surface must lie.

    So in any one foot section, the entire surface of the part must be within .002" of every other portion of the...
  19. No experience on the Tsugami end. I can tell you...

    No experience on the Tsugami end. I can tell you the Citizen version works wonderfully for things like gun drilling, and chip control on your deeper/longer cuts/stringy materials.
  20. Replies
    7
    Views
    561

    In a machine shop? It's what you get from the...

    In a machine shop?

    It's what you get from the scrappers for 20 million dollars worth of carbide tooling.
  21. Don't think he's a spammer, just a neophyte. His...

    Don't think he's a spammer, just a neophyte. His other posts are about a mill he just bought...
  22. Replies
    7
    Views
    561

    MITGI | Precision micro cutting tool manufacturer...

    MITGI | Precision micro cutting tool manufacturer since 1993.

    Call these guys. Tell them what you want. They'll make 'em custom, in about a week.
  23. Replies
    81
    Views
    7,684

    Checked my email... Not sure which email I signed...

    Checked my email... Not sure which email I signed up to the forum with, but I don't see anything in my inbox. I did clear out PM space here though, sorry about that.
  24. Replies
    512
    Views
    33,935

    I'm rather more incredulous that anyone believes...

    I'm rather more incredulous that anyone believes a new F150 is worth $80K.... When you can, in fact, buy a Tesla Model X, which has WAY MORE technology (albeit probably lower R&D costs because of a...
  25. Replies
    19
    Views
    915

    And if it's a 4-40, I'd hope like heck he's using...

    And if it's a 4-40, I'd hope like heck he's using a feedrate of .025/Rev
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4