Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: BHolcombe

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    7
    Views
    385

    I have plenty of them, I just only have them up...

    I have plenty of them, I just only have them up to a 3.5" diameter.

    I tram the mill and tip the spindle about .0005" over a few inches (typical sweep), enough that the cutter doesn't cut on the...
  2. Replies
    7
    Views
    385

    Thank you, appreciate the reply. I intend to use...

    Thank you, appreciate the reply. I intend to use it only for light cuts. I dislike the appearance of multiple passes on a finished surface so often enough I'll take a finished part and have it...
  3. Replies
    7
    Views
    385

    Thank you for clearing up my confusion. I...

    Thank you for clearing up my confusion. I assumed facing was the same as face milling, but that makes much more sense that one would face a bored hole after making it.

    As mentioned, I did not do...
  4. Replies
    7
    Views
    385

    Boring/Facing or dedicated fly cutter?

    Is a boring/facing setup like that produced by Gamet/Enco capable of providing a perfectly clean surface finish so much that something dedicated to fly cutting like those produced by suburban tool...
  5. Thanks, Mike. That is a great resource, much...

    Thanks, Mike. That is a great resource, much appreciated.
  6. Thanks for your insights. It sounds like it...

    Thanks for your insights. It sounds like it would be best to make a set of large sized parallels and use the machine's vise to complete this task.

    The table I had made will be handy for keeping...
  7. The issue I'm solving is that the machine table...

    The issue I'm solving is that the machine table is small along with the work envelope along the Y-axis, so I dont have room for a vise (the machine table is a vise). I dont need to make angled cuts...
  8. Thanks for the replies. Thermite, thank you...

    Thanks for the replies.

    Thermite, thank you for this information and forgive my ignorance please. I've been under the assumption that sine plates were commonly used for light milling and grinding...
  9. Favorite hold down clamps for a small sine plate?

    Bought a 6" sine plate recently and I'm realizing that when utilizing a typical step-clamp setup that I will find that gravity has become my enemy when I do a production run.

    What are your...
  10. Replies
    3
    Views
    1,461

    Vincent, trouble you for the dimensions on this?

    Vincent, trouble you for the dimensions on this?
  11. Replies
    5
    Views
    829

    Thank you, I ended up reaching out to a custom...

    Thank you, I ended up reaching out to a custom maker to have a plate made in cast iron.
  12. Replies
    5
    Views
    829

    This is for a mortising machine (woodworking...

    This is for a mortising machine (woodworking tool). I hesitated to mention it because I find the 'wood moves, who cares' sentiment to get in the way of useful advice.

    On the machine I have and...
  13. Replies
    5
    Views
    829

    Preferred maker of Grid plates?

    Howdy,

    I have a machine new to the shop that has an open table, basically you can mount your own setup to it or use the existing built in clamp for typical work.

    I would like to add a grid...
  14. Replies
    12
    Views
    1,343

    Sounds like I should have posted a wanted add...

    Sounds like I should have posted a wanted add when I was looking for those. They're very handy for small work, I used them to make a set of 45 degree hinges not long ago.
  15. Replies
    12
    Views
    1,343

    These look like a really smart design. I have...

    These look like a really smart design. I have Kurt 3 in 1 jaws for one vise, they're very useful but can only manage basic angles like 15, 30, 45.
  16. Replies
    12
    Views
    1,343

    I spoke with Kurt about the 'sine' aspect of...

    I spoke with Kurt about the 'sine' aspect of this, apparently it is built in currently. I'm not sure what that actually entails however. I am curious to find out.
  17. Replies
    4
    Views
    1,187

    Thanks for the replies, I have someone interested...

    Thanks for the replies, I have someone interested in the work.
  18. Replies
    4
    Views
    1,187

    The diameter of the shoulder is .625" and it's...

    The diameter of the shoulder is .625" and it's .187" long. Sorry, I can see how my wording above is confusing.

    I can provide a drawing for anyone interested, and I purchased all of the reamers...
  19. Replies
    4
    Views
    1,187

    Need a few steel bushings made

    Hi,

    I need three bushings made for a piece of machinery. These bushings are shown here:

    https://www.advancedmachinery.co.uk/content/product/341_0_z.jpg

    I would, of course, buy them but...
  20. Replies
    12
    Views
    1,343

    KURT KTR35 'Sine' Toolroom vise

    Good afternoon! Wondering if anyone has experience with this vise, do you like the function of it?

    I'm thinking to use this one one of a few machines for easy setup of angles.
  21. I brought the brass to 1500 grit on a plate prior...

    I brought the brass to 1500 grit on a plate prior to tumbling. Nice tumbled finish after 2-3 hours in the tumbler after that work.

    Not thrilled, but I want to minimize how much the corners are...
  22. Thank you! That is very helpful.

    Thank you! That is very helpful.
  23. Sounds good, I guess I'll just experiment and see...

    Sounds good, I guess I'll just experiment and see what works best.
  24. I want to show my 'lapping' results also, since I...

    I want to show my 'lapping' results also, since I think it's relevant here.

    This is the result of those nickel silver hinges as lapped prior to bead blasting.
    ...
  25. I do manual machining and the great majority of...

    I do manual machining and the great majority of it is on a Bridgeport. I make things as demand warrants them, so not always the same product but here are two examples.

    I made this set of hinges....
Results 1 to 25 of 34
Page 1 of 2 1 2