Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Flute Maker

Page 1 of 16 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    794

    The phone number appears to be wrong, and the guy...

    The phone number appears to be wrong, and the guy who answered said it's been wrong for many years! The web has no other info.

    Payson.
  2. Replies
    3
    Views
    794

    Thank you. I'll call them in the morning. ...

    Thank you. I'll call them in the morning.

    Best,

    Payson.
  3. Replies
    3
    Views
    794

    End Mill / Drill Sharpen Resource

    Hi folks,

    Anyone familiar with a grinding shop to sharpen mills and drills in the New England area?

    Thanks,

    Payson.
  4. Replies
    0
    Views
    896

    Burgmaster OB manual free.

    Just found a manual with parts breakout for a Burgmaster OB. Anyone need it? I can scan and email it too. No money.

    PG
  5. It's 100v so the ground should be obvious, Green?...

    It's 100v so the ground should be obvious, Green? Then do what Johansen says. I think 1/3 hp is a little light.

    PG
  6. I believe there's a taper pin on the v-belt...

    I believe there's a taper pin on the v-belt pulley. My friend just replaced the bearings and shaft on his because the bearings were worn through and chewed up the shaft.

    Payson.
  7. Replies
    4
    Views
    1,532

    Thanks Digger. These are used on special bench...

    Thanks Digger.
    These are used on special bench lathes, in the production of musical instruments. What we have a stamped. I'm hoping to pay under $10. Sopkos must be a lot more than that.

    Payson.
  8. Replies
    4
    Views
    1,532

    Need Grinding Wheel Arbor Washers

    I need to find some raised center washers, for grinding wheel arbors. They are steel, 3"D x .110" Th.+- x .500" H. The center area is raised for about 1.150"D.

    Thanks,

    Payson.
  9. Replies
    0
    Views
    496

    South Bend 9" Belt Guard

    A friend closed his shop and i grabbed some stuff he was throwing out. Here's 2 beltguards he made. No charge, unless i have to ship.
    Maybe someone around the Boston area can use them.
    ...
  10. Replies
    0
    Views
    479

    13" In Newton MA.

    Southbend 13" Lathe - tools - by owner - sale

    Not mine. Just saw it on Craigslist.

    PG
  11. Replies
    7
    Views
    825

    Done. Thanks. In our #16 clutch sleeve there's...

    Done. Thanks.
    In our #16 clutch sleeve there's a screw with a spring under it, that seems to run against a knurl on the tube. I opened up my 10K closer and found the same thing. There's a plastic /...
  12. Replies
    7
    Views
    825

    That's just what I was looking for. I can push up...

    That's just what I was looking for. I can push up the ring, but bringing it forward is the trick. I'll bend a tool when I get in on Monday.

    Thanks so much,

    Payson.
  13. Replies
    7
    Views
    825

    It's #18, shaft snap ring. Problem is that it...

    It's #18, shaft snap ring. Problem is that it disappears under the #16 clutch sleeve, and very hard to see, and remove.

    Payson.
  14. Replies
    7
    Views
    825

    Thanks. I send you a picture on Monday. It’s at...

    Thanks. I send you a picture on Monday. It’s at work.
    Payson
  15. Replies
    7
    Views
    825

    9" lever Closer Disassemble

    Good morning everyone,
    How do I get the snap ring off the shaft, to slide the collar off?

    Thanks,

    Payson.
  16. Replies
    766
    Views
    535,123

    Oh I like that. Any name on it? Payson

    Oh I like that. Any name on it?
    Payson
  17. Thread: Die Making

    by Flute Maker
    Replies
    2
    Views
    607

    So sorry I neglected to thank Larry for the...

    So sorry I neglected to thank Larry for the information, and links. When we started to use this thread size, well over 20 years ago, we didn't find a die on the shelf anywhere, so we didn't look...
  18. Thread: Die Making

    by Flute Maker
    Replies
    2
    Views
    607

    Die Making

    Happy New Year to all. I would like to have a few #4x72 dies made. Anyone do this here?

    Thanks,

    Payson.
  19. Replies
    3
    Views
    473

    Thank you. Much appreciated. I couldn't find it....

    Thank you. Much appreciated. I couldn't find it. NOW, I need a source for the round split ring on the OD, that keeps the pin in the body, as well as the pin dimensions.

    Payson.
  20. Replies
    3
    Views
    473

    9" Lever Closer Diagram

    Hi folks,
    Can someone direct me to an exploded view of a 9" lever closer please.

    Thanks,

    Payson.
  21. Replies
    3
    Views
    625

    Riten / Concentric Center Parts

    Hi Folks,

    Does Riten sell parts for live centers? They only describe sending them in for a rebuild, on their website.

    Thanks,

    Payson.
  22. Dunham Pneumatic Collet Closer & Hardinge HF-1A Bar Feed

    Hi guys,

    Does anyone have experience with the Dunham DACC collet closer?
    I'm also looking for the Hardinge HF-1A 24" bar feed manual.

    Thanks,

    Payson
  23. Replies
    2,290
    Views
    445,243

    Sticky: Saved At The Bell

    I'm always happy to read posts like this. Good luck with it.

    Payson.
  24. Replies
    3
    Views
    858

    Need 40 deg. #1 Center Drill.

    Hi. I need some HSS centerdrills made with a 20 degree per side / included angle. Maybe 1 dz. Standard length, or longer is ok too.

    Thanks,

    Payson.
  25. Replies
    766
    Views
    535,123

    Whats This Vise?

    A friend has this for sale, really really cheap, in Waltham MA. No branding on it.

    Payson.
Results 1 to 25 of 389
Page 1 of 16 1 2 3 4