Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: SBLatheman

Page 1 of 60 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    3
    Views
    195

    IF this index plate is original, then the machine...

    IF this index plate is original, then the machine was made in 1975 or later.
    According to Steve Wells, the “O” means that it has a D1-4 spindle. I have seen others that had the “O” that did not have...
  2. Replies
    23
    Views
    1,330

    Bill, The compound in the picture is not a...

    Bill,
    The compound in the picture is not a South Bend. This one has two screws to attach it to the cross slide and just a pin in the center for the pivot, I don’t know the brand. The cross slide is...
  3. Replies
    23
    Views
    1,330

    I have the one in the picture...2 3/4” travel...

    I have the one in the picture...2 3/4” travel
    $90 plus $15 shipping
    Ted
    [email protected]
  4. Replies
    23
    Views
    1,330

    How much travel do you need ?

    How much travel do you need ?
  5. Replies
    5
    Views
    945

    I have a manual. Send me an email Ted...

    I have a manual.
    Send me an email
    Ted
    [email protected]
  6. Replies
    25
    Views
    1,835

    I installed the motor and all the wiring on the...

    I installed the motor and all the wiring on the machine today. Smooth and quiet :)
    ...but, as luck would have it, forward/reverse is backwards :rolleyes5:
    I assume I need to switch the red and...
  7. Replies
    25
    Views
    1,835

    Eureka ! ! That worked :o Thank you very much,...

    Eureka ! ! That worked :o
    Thank you very much, Allan, you certainly know what you are talking about :)
    Thanks again,
    Ted
  8. Replies
    25
    Views
    1,835

    More info: The brown goes to the centrifugal ...

    More info:
    The brown goes to the centrifugal switch
    The black wire goes to the capacitor
    Red goes into the windings, and so do the yellow ones.

    Thanks for everybody’s help :)
    Ted
  9. Replies
    25
    Views
    1,835

    I had time this morning to wire it up.(on the...

    I had time this morning to wire it up.(on the bench)
    Flipped the switch on direction and the motor started right up, a little rough running. Shut it off and flipped it the other direction. It...
  10. Replies
    8
    Views
    749

    It is a D1-8...that was the only spindle nose...

    It is a D1-8...that was the only spindle nose offered.
  11. Replies
    25
    Views
    1,835

    Thank you, Allan. That is a very elegant...

    Thank you, Allan. That is a very elegant solution...if it works:)
    I will test the capacitor like you suggested first and let you know how it worked out.
    Regards,
    Ted
  12. Replies
    12
    Views
    628

    I thought that machine looked too big to be a 13”...

    I thought that machine looked too big to be a 13” :skep:
    It is a 16”, as shown by the index plate
    Ted
  13. Replies
    25
    Views
    1,835

    They are pretty good pictures, but they don’t...

    They are pretty good pictures, but they don’t post very well:confused:
    I can email them to you.
    Ted
    [email protected]
  14. Replies
    25
    Views
    1,835

    Wiring motor/switch help...Please

    Wiring motor/ switch help...Please

    This motor is on a Heavy 10 that I bought. The previous owner had replaced the 3-phase motor with this Dayton, wired to just run forward(220v 1-phase). I want it...
  15. Replies
    5
    Views
    945

    The CS33 was made in Spain by METOSA. South Bend...

    The CS33 was made in Spain by METOSA. South Bend imported them for a few years, then Clausing picked them up. You should be able to get parts from them.
    (I still have a few parts)
    Ted
  16. Replies
    17
    Views
    880

    The wiper retainers you have are not for the...

    The wiper retainers you have are not for the Heavy 10. I don’t think they are South Bend.
    Ted
  17. Replies
    2,290
    Views
    445,243

    Sticky: Steve, This machine is a horizontal drive. I...

    Steve,
    This machine is a horizontal drive. I don’t think the bench is original.
    Ted
  18. Replies
    34
    Views
    2,666

    I have a N.O.S. replacement TS spindle for the...

    I have a N.O.S. replacement TS spindle for the 16” for sale.
    It is the high dollar hardened and ground option(the ID and threads are hard, not the OD)
    It has a few pits from a little rust it had....
  19. Replies
    1
    Views
    583

    Send me an email :typing: Ted [email protected]

    Send me an email
    :typing:
    Ted
    [email protected]
  20. Replies
    1
    Views
    479

    I have a 6” Bison adjust tru chuck back for sale...

    I have a 6” Bison adjust tru chuck back for sale (A1-5)...$75 plus shipping
    Email if interested.
    Ted
    [email protected]
  21. Replies
    3
    Views
    799

    The brake is controlled by a TDR (time delay...

    The brake is controlled by a TDR (time delay relay)...yours is probably bad.
    Ted
  22. Replies
    2
    Views
    656

    That is a 9” serial number. Ted

    That is a 9” serial number.
    Ted
  23. Thread: old newbie

    by SBLatheman
    Replies
    1
    Views
    498

    Pretty good chance 😁 Send me an email. Ted...

    Pretty good chance 😁
    Send me an email.
    Ted
    [email protected]
  24. For the record: Volitan purchased the smaller of...

    For the record: Volitan purchased the smaller of the two springs I have.
    The large one is still available in case someone is searching for one in the future.
    Thanks,
    Ted
  25. Yes, see pictures. The first one is about 4 1/4”...

    Yes, see pictures.
    The first one is about 4 1/4” diameter .038” x 1”
    The second one is ~3 1/4” diameter .035”x 1”
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4