Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: wmpy

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    31
    Views
    2,236

    I'm guessing that the prices quoted do not...

    I'm guessing that the prices quoted do not include the buyer's premium, so you can tack on an additional 18% to those prices.
  2. Replies
    31
    Views
    2,236

    Curious if you know what those Hermles went for?

    Curious if you know what those Hermles went for?
  3. Thanks for all the good info. Once this goes into...

    Thanks for all the good info. Once this goes into full production, I'll have more time to dial it in. Hopefully, the few inserts I ordered to test will get me through this prototype run. On my list...
  4. Diameter is about 2.5". Length is less than 1"....

    Diameter is about 2.5". Length is less than 1". We're just turning to clean up the casting- I'd say about .050" per side. There are 6 large windows in the part. There are more voids than there is...
  5. I've got a Walter WKK20S for the roughing and a...

    I've got a Walter WKK20S for the roughing and a Seco TK1501 for the finishing scheduled to be delivered tomorrow, so I'll see how those cut. I've also got some other inserts From Tungaloy, Sumitomo,...
  6. The interruptions in the part leave some fragile...

    The interruptions in the part leave some fragile bits that I was afraid to use a flat top insert on. I might give it a try, though.

    Inserts I'm using are WNMG432 for roughing and DNMG431 for...
  7. Insert recommendation for turning ductile iron

    Hi all. It's been a while since I've done any turning on ductile. I'm setting a job up with some steel cutting carbide inserts, and it's wearing them out crazy fast. I'm taking light, very...
  8. Thread: Opening chuck

    by wmpy
    Replies
    16
    Views
    825

    M11 / M10 on my Nakamura

    M11 / M10 on my Nakamura
  9. This machine has sold.

    This machine has sold.
  10. The Mori DL20MC that was linked to earlier is...

    The Mori DL20MC that was linked to earlier is mine. I just sold it on Friday.
  11. Replies
    2
    Views
    401

    On my BNC-34S, the turret indexing is done with a...

    On my BNC-34S, the turret indexing is done with a hydraulic motor. There are two solenoid valves on the back of the turret that control the indexing. They are really easy to find at the back of the...
  12. Thanks for the bump, guys. The Mori is still for...

    Thanks for the bump, guys. The Mori is still for sale. It was moved out of place to make room for the new stuff, so it's just sitting in the back of the shop now. I do think it's a lot of machine for...
  13. Replies
    33
    Views
    2,999

    I don't think Intertech is around anymore. For a...

    I don't think Intertech is around anymore. For a similar machine, though, check out Quick-Tech. They actually show one later in that same video. Quick-Tech is a division of Tongtai, which I've had an...
  14. Replies
    8
    Views
    926

    Hey Rob, is that "feed 15% of radius" thing for...

    Hey Rob, is that "feed 15% of radius" thing for real? I had never heard it before. So a CNMG431 should be programmed at about 0.0025 ipr? Seems a bit light, but I do like the idea of the feed being...
  15. Replies
    3
    Views
    505

    I agree with the previous posters... but just in...

    I agree with the previous posters... but just in case it's not the material, I would check the following things.

    Is the bar bent?

    Is the GB in alignment with the collet?

    Is the collet set to...
  16. Replies
    33
    Views
    2,999

    I'm going to add my vote for the Miyano BNC-34S....

    I'm going to add my vote for the Miyano BNC-34S. I have one with an FMB bar loader, and it's a great machine. It's the first thing I thought of when I read your description of what you needed. 34 mm...
  17. Replies
    6
    Views
    668

    I think it's important here to know what M110...

    I think it's important here to know what M110 does. I believe on a Daewoo it removes the stroke limit barriers. If that's the case, then it seems to me that it would be much more difficult to...
  18. Replies
    4
    Views
    1,173

    The Wisconsin Manufacturing Technology Show...

    The Wisconsin Manufacturing Technology Show alternates years with IMTS.

    Home - The Wisconsin Manufacturing & Technology Show
  19. So you would use this in the place of spare M...

    So you would use this in the place of spare M codes if your machine wasn't equipped with them?
  20. Replies
    6
    Views
    757

    I was looking for some VDI tooling on ebay...

    I was looking for some VDI tooling on ebay recently and came across this.


    Tool Holder VDI 30 MADAULA | eBay
  21. This machine has sold.

    This machine has sold.
  22. Mori Seiki DL-20MC Dual Spindle, Dual Turret 6-axis CNC Lathe with Live Tools

    Hello,

    I have four CNC lathes that I am looking to sell in order to make room for some newer machines that I have purchased. The nature of our work has changed over the years, and these machines...
  23. I can go somewhere else to sell them or wait to...

    I can go somewhere else to sell them or wait to sell.
  24. This week I was quoted: brass chips $1.55/lb...

    This week I was quoted:

    brass chips $1.55/lb
    aluminum solids $0.36/lb
    stainless chips $0.27/lb

    Any thoughts whether these prices are fair?
  25. I would really like to get this machine sold by...

    I would really like to get this machine sold by next week. Please make an offer if you are considering it.
Results 1 to 25 of 87
Page 1 of 4 1 2 3 4