Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: 1yesca

Page 1 of 33 1 2 3 4

Search: Search took 0.01 seconds.

  1. FS lit champ mod 10-10A Broach Key way Cutting Kit

    this treadwell lit champ mod 10-10A Broach Key way Cutting Kit is in vary good cond. with vary little uses . kit comes with 6 cutters 1/16" #0 , 1/8" #1 , 3/16" #2 , 1/4" #2 , 5/16" #2 and 3/8" #2 ....
  2. Replies
    8
    Views
    747

    maybe for drilling holes in electronic circuit...

    maybe for drilling holes in electronic circuit boards
  3. Replies
    38
    Views
    2,897

    like that sting song [when you find your servant...

    like that sting song [when you find your servant is your master] or top rail now on the bottom
  4. Replies
    45
    Views
    3,088

    as val the russian would say plus or minus one...

    as val the russian would say plus or minus one bus stop
  5. Replies
    27
    Views
    1,116

    some are some are not . in your case i would bet...

    some are some are not . in your case i would bet there is no run cap in your motor and to see if it is or is not get that thing on a bench with a power cord and some wire nuts . get on with it...
  6. Replies
    27
    Views
    1,116

    that's good because that motor you have in your...

    that's good because that motor you have in your op don't run / operate on 236 / 220 / 240 it runs on 115/120 ya and i know your talking about the rated voltage of the run cap so use a 220 / 240 volt...
  7. Replies
    27
    Views
    1,116

    yup just like a lot of condenser fan motors on...

    yup just like a lot of condenser fan motors on a/c units the run cap is external it can be mounted on the motor or by the motor
  8. Replies
    7
    Views
    620

    so try resetting [by removing and reinstalling]...

    so try resetting [by removing and reinstalling] the two sets of wired together brushes so there 90 degrees apart [instead of the brush jumpers being left right they would be top bottom
  9. Replies
    27
    Views
    1,116

    yup there's a run cap . this is child's play all...

    yup there's a run cap . this is child's play all the info is there just test wire it up on a bench with a cap and cord and a few wire nuts as mike hadeck would say it ain't no big deal
  10. Replies
    27
    Views
    1,116

    that switch looks like a 3 pole single throw on...

    that switch looks like a 3 pole single throw on off like for a 3 ph. circuit that's a lot of switch for that that circuit . but i do agree with rons being it only shows one rpm more then likely its...
  11. Replies
    31
    Views
    1,774

    there's going to be hell to pay when the...

    there's going to be hell to pay when the thermster see this one
  12. Replies
    0
    Views
    277

    any one in need of a GE 9T51B8 Transformer

    i have this General Electric GE 9T51B8 Transformer 1PH 0.5KVA 240/480V-AC 120/240V-AC that needs a new home $100 shipped


    328245328246
  13. Replies
    14
    Views
    1,534

    1/4 x 22 why lots of metal and when you have some...

    1/4 x 22 why lots of metal and when you have some kid that came off a farm installing a screw and the only thing he ever screwed before was his sister paul did not want him cross treading it and it a...
  14. Replies
    11
    Views
    5,566

    a parrot strangler i believe P&W made some of the...

    a parrot strangler i believe P&W made some of the taps for them . they are handy for saving a barrel that was a bit to short


    328144328143
  15. Replies
    23
    Views
    1,480

    if it were the size of the guttenburg bible who...

    if it were the size of the guttenburg bible who could have afforded to buy it . its not a bed side reader it a reference book that needed to be handy when you need it and not take up a lot of room
  16. Replies
    23
    Views
    1,546

    yup its right up there with the hydraulic...

    yup its right up there with the hydraulic distributor that was on some of the tucker cars that operated the valves
  17. Replies
    23
    Views
    1,546

    the ball bearings were moving inside the tube ....

    the ball bearings were moving inside the tube . the tube had a 180 deg. bend . so the push rod was at one end of the fixed tube pushing the balls in as the push rod went up and the balls at the other...
  18. i think i have one of them set ups they are held...

    i think i have one of them set ups they are held together at each end by allan head cap screws i will have to take a pic and post . well looks like i tripped on my foreskin the one i have is a...
  19. Replies
    14
    Views
    1,534

    A gunsmith in training ? when my dad had his shop...

    A gunsmith in training ? when my dad had his shop there were these people that would come in every now and then with the shoe box with a gun of some sort all apart and it was always there kid that...
  20. Replies
    23
    Views
    1,546

    that's right up there with the after market OHV...

    that's right up there with the after market OHV model T head a guy showed me 40 something years ago that instead of a rocker arm had a harden curved tube full of ball bearings
  21. Replies
    23
    Views
    1,546

    its not a 10EE when i first started in the...

    its not a 10EE when i first started in the automotive field i was talking to my mentor i was saying how it would be interesting to take a car and balance every thing on the drive train his reply...
  22. that's funny . hey grandma what's shaking . or...

    that's funny . hey grandma what's shaking . or the ol dodge ads back in the late 60's and early 70's with the racing grandma saying [ put a dodge in your garage sonny ]
  23. Replies
    16
    Views
    1,461

    if its a one off and a labor of love ok but if...

    if its a one off and a labor of love ok but if you want to keep your hair and or your a smith doing it as a paying job then . now it would be interesting to see how the big boys are doing it .
  24. Replies
    33
    Views
    5,871

    7 x 33 ya good luck with that

    7 x 33 ya good luck with that
  25. i work in an automotive machine shop there is...

    i work in an automotive machine shop there is this shyster that we do work for. his gig renumbering run of the mill Chevy blocks in to Chevy corvette blocks . i could be wrong but its my...
Results 1 to 25 of 815
Page 1 of 33 1 2 3 4