Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: bll230

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Use a lathe,(hopefully you have another one) to...

    Use a lathe,(hopefully you have another one) to make a large aluminum/brass ring that fits precisely around the diameter where the pin is, drill and tap for a pusher bolt, and then cut in half to...
  2. Tach disassembly question - 1956 10EE square dial

    While my lathe is running there is a very slight rubbing noise coming from the tach. Does anyone have any suggestions on disassembling the tach?

    I read Focus's thread,
    ...
  3. Replies
    17
    Views
    1,086

    Sikorsky in Stratford, Ct. was/is the same. 4x4...

    Sikorsky in Stratford, Ct. was/is the same. 4x4 sections on end. Had been there since WW 2 or so.
  4. As an (hopefully talented) aeronautical engineer...

    As an (hopefully talented) aeronautical engineer with a deficient ability to understand EE stuff, thank you very much for this work.
  5. Replies
    8
    Views
    569

    For My 10EE I had great luck getting bearings...

    For My 10EE I had great luck getting bearings from LocateBB on Ebay. I think every bearing I searched for they came up as a seller(except the spindle bearings). I did have to message them so when I...
  6. Replies
    5
    Views
    475

    I've got one, I just need collets for it.

    I've got one, I just need collets for it.
  7. Willy, you mention another gear source. I doubt...

    Willy, you mention another gear source. I doubt Monarch makes gears any longer. If they do not have leftover inventory from decades ago, they probably contract with a gear shop. As far as price...
  8. I am the owner of Bill’s former small frame...

    I am the owner of Bill’s former small frame Reliance, Presently in my lathe. My original motor with the smoked armature I took to a motor rebuilding shop and was quoted minimum $1500 for a rewind,...
  9. My 10EE bushings were worn as well, with similar...

    My 10EE bushings were worn as well, with similar but not so extreme wear on the gears. I bored out the bushings and fitted new inners on the bushings, so to speak. I flipped the worm around so it...
  10. $176. I really only wanted the 4 sizes for $100,...

    $176. I really only wanted the 4 sizes for $100, but 13 bits for $176 seemed ok. Most of the time I am just removing material to continue boring.

    13 PC 17/32-1" VIKING S&D- SILVER & DEMING DRILL...
  11. I got my Viking/Norse drill bits from Ebay. They...

    I got my Viking/Norse drill bits from Ebay. They are very nice and this time undamaged. The Ebay seller was Sandy56blue. The price was fair, in my opinion, and he wrapped all the bits individually...
  12. Replies
    32
    Views
    2,167

    Here is a question I've been wondering about. ...

    Here is a question I've been wondering about. The tail stock nut is simply a piece of brass/bronze that has an Acme thread, Not even oddly shaped like the cross slide nut. What is difficult to...
  13. Thanks, I ordered a 13 piece set off ebay. seller...

    Thanks, I ordered a 13 piece set off ebay. seller says he will wrap individually. I mistakenly said the 8 piece set earlier.
  14. Replies
    32
    Views
    2,167

    Zap, sorry, I forgot to say, CrazyMonkey asked...

    Zap, sorry, I forgot to say, CrazyMonkey asked for the handle. As it is CM, Rakort, and Lectrician got their parts, nobody else has asked for what I have remaining.
  15. Replies
    13
    Views
    927

    Mine had a ball bearing, no gap

    Mine had a ball bearing, no gap
  16. Rich asked me to post the pic, but I see Cal...

    Rich asked me to post the pic, but I see Cal fixed it. I don't know what funkyness is going on with Apple either, but my solution is I take pics with iphone, email to myself, I use yahoo mail, make...
  17. I just bought an 8 piece set on ebay, the one...

    I just bought an 8 piece set on ebay, the one with them standing in a wood block. I have asked the seller how he plans to ship them. Thanks for the tip.

    John
  18. I have not read all the posts, so forgive me if I...

    I have not read all the posts, so forgive me if I repeat something. I am using the Parker 514/507 setup that Bill developed, and I have wired in relays to make the ELSR work as original. I have cut...
  19. Replies
    9
    Views
    841

    Minor update today. I tried using the closer...

    Minor update today. I tried using the closer today and there was binding somewhere. The difference: the lathe wasn't running today and the spindle was cold. The 1 3/8 tubing is not precise, there...
  20. Replies
    9
    Views
    841

    Something to keep in mind. I have started my...

    Something to keep in mind. I have started my South Bend 9 many times with an unsecured 3C collet closer in it. Rattle, rattle, no big deal. I'll come up with a mental procedure to ensure the...
  21. Replies
    9
    Views
    841

    A very tight thermal fit, about 350 degrees...

    A very tight thermal fit, about 350 degrees worth, and then Loctite 290 wicked in while the aluminum was still hot and expanded. The 290 is so strong it will never let go.
  22. You're right - the nicks and dings aren't too...

    You're right - the nicks and dings aren't too bad. On the other hand, I can use my Chinese nicked and dinged bits for free. I just don't want to be out $100 to use nicked and dinged bits. I would...
  23. You know, today I had that thought, ordering them...

    You know, today I had that thought, ordering them individually. I called Norse this morning and had a long conversation with customer service. I explained that the blow molded case was sized for...
  24. See first post about Viking/Norseman....

    See first post about Viking/Norseman....
  25. Looking for Made is US Silver and Deming drill bits

    I want to replace my Chinese junk bits with US made S&D drill bits. I came across Norse/Viking tool and tried those, but they package their 4 piece set in a blow molded case that does not properly...
Results 1 to 25 of 478
Page 1 of 20 1 2 3 4